Instrument Panel Cluster (IPC) DTC Chart
INSTRUMENT PANEL CLUSTER (IPC) DTC CHART
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor A Circuit: Circuit Short to Ground | For Front Wheel Drive (FWD), Go To PINPOINT TEST B . For All-Wheel Drive (AWD), Go To . |
| P0460:13 | Fuel Level Sensor A Circuit: Circuit Open | For FWD
, Go To PINPOINT TEST B . For AWD , Go To PINPOINT TEST C . |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure |
Go To PINPOINT TEST C . |
| P1346:11 | Fuel Level Sensor B Circuit: Circuit Short to Ground | Go To PINPOINT TEST C . |
| P1346:13 | Fuel Level Sensor B Circuit: Circuit Open | Go To PINPOINT TEST C . |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub-Type Information |
Go To PINPOINT TEST AB . |
| P174F:23 | Traction Control Enable/Disable Switch Lamp Circuit: Signal Stuck Low |
REFER to VEHICLE DYNAMIC SYSTEMS . |
| B109E:42 | Remote Keyless Entry: General Memory Failure | REFER to HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS . |
| B109E:51 | Remote Keyless Entry: Not Programmed | REFER to HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS . |
| B109E:86 | Remote Keyless Entry: Signal Invalid | REFER to HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS . |
| B10D5:13 | PATS Antenna: Circuit Open | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D7:05 | PATS Key: System Programming Failure | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D7:51 | PATS Key: Not Programmed | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D7:87 | PATS Key: Missing Message | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D7:8F | PATS Key: Erratic | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D8:00 | PATS
Key Less Than Minimum Programmed: No Sub-Type Information |
REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10D9:87 | PATS Transponder: Missing Message | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10DA:51 | PATS PCM Identifier: Not Programmed | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10DA:61 | PATS PCM Identifier: Signal Calculation Failure | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B10DA:86 | PATS PCM Identifier: Signal Invalid | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| B1A82:09 | External Trip Switch: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1A82:09 returns, INSTALL a new HVAC module (without navigation) or Front Controls Interface Module (FCIM) (with navigation). REFER to CLIMATE CONTROL (without navigation) or INFORMATION AND ENTERTAINMENT SYSTEMS (with navigation). |
| B1A82:11 | External Trip Switch: Circuit Short to Ground | Go To PINPOINT TEST AC . |
| B1A82:13 | External Trip Switch: Circuit Open | Go To PINPOINT TEST AC . |
| U0002:88 | High Speed CAN Communication Bus Performance: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U0011:88 | Medium Speed CAN Communication Bus Performance: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U0100:00 | Lost Communication With ECM /PCM "A": No Sub-Type Information | Go To PINPOINT TEST AO . |
| U0102:00 | Lost Communication With Transfer Case Control Module: No Sub-Type Information | Go To PINPOINT TEST AP . |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub-Type Information | Go To PINPOINT TEST AQ . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub-Type Information | Go To PINPOINT TEST AR . |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information |
Go To PINPOINT TEST AS . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub-Type Information |
Go To PINPOINT TEST AT . |
| U0154:00 | Lost Communication With Restraints Occupant Classification Sensor (OCS ): No Sub-Type Information | Go To PINPOINT TEST AU . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub-Type Information | Go To PINPOINT TEST AV . |
| U0161:00 | Lost Communication With Compass Module: No Sub-Type Information |
REFER to ELECTRONIC COMPASS . |
| U0163:00 | Lost Communication With Navigation Control Module: No Sub-Type Information | Go To PINPOINT TEST AW . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub-Type Information |
Go To PINPOINT TEST AX . |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub-Type Information | Go To PINPOINT TEST AY . |
| U0214:00 | Lost Communication With Remote Function Actuation: No Sub-Type Information | Go To PINPOINT TEST AZ . |
| U0241:00 | Lost Communication With Headlamp Control Module "A": No Sub-Type Information | Go To PINPOINT TEST BA . |
| U0242:00 | Lost Communication With Headlamp Control Module "B": No Sub-Type Information | Go To PINPOINT TEST BB . |
| U0401:00 | Invalid Data Received from ECM /PCM A: No Sub-Type Information | DTC U0401:00 is set when the IPC receives invalid network data from the PCM with a faulted vehicle speed input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for a list of all DTCs. |
| U0401:29 | Invalid Data Received from ECM
/PCM A: Signal Invalid |
DTC U0401:29 is set when the IPC receives invalid network data from the PCM with a faulted tachometer input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for a list of all DTCs. |
| U0401:86 | Invalid Data Received from ECM
/PCM A: Signal Invalid |
DTC U0401:86 is set when the IPC receives invalid network data from PCM with a faulted engine coolant temperature input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for a list of all DTCs. |
| U0405:55 | Invalid Data Received from Cruise Control Module: Not Configured | DTC U0405:55 is set when the IPC
receives adaptive cruise control data when the IPC
is not configured for adaptive cruise control in the IPC
configuration. CARRY OUT the Programmable Module Installation (PMI) procedure for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation. |
| U0422:55 | Invalid Data Received from Body Control Module: Not Configured |
DTC U0422:55 is set when the IPC
receives Smart Junction Box (SJB) data when the IPC
is not configured for the system or function in the IPC
configuration. CARRY OUT the PMI procedure for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation. |
| U0430:00 | Invalid Data Received from Tire Pressure Monitor Module: No Sub-Type Information |
DTC U0430:00 is set when the IPC
receives invalid network data from SJB
with a faulted Tire Pressure Monitoring System (TPMS) input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for a list of all DTCs. |
| U0462:00 | Invalid Data Received from Compass Module: No Sub-Type Information | REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| U2100:00 | Initial Configuration Not Complete: No Sub-Type Information | CARRY OUT the PMI procedure for the IPC . REFER to MODULE CONFIGURATION . |
| U3000:41 | Control Module: General Checksum Failure | self-test. If DTC U3000:41 returns, INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) . TEST the system for normal operation. |
| U3000:42 | Control Module: General Memory Failure | INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) . TEST the system for normal operation. |
| U3000:44 | Control Module: Data Memory Failure | INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) . TEST the system for normal operation. |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go To PINPOINT TEST BC . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go To PINPOINT TEST BD . |
| U300A:62 | Ignition Switch: Signal Compare Failure | Go To PINPOINT TEST BE . |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | GO to PINPOINT TEST BE . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history