LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2008 >> MKX FWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Information Center >> Diagnostic Tests >> Instrument Cluster (IC), Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test W: The O/D Off Indicator Is Never/Always On

Pinpoint Test W: The O/D Off Indicator Is Never/Always On

Normal Operation 

The instrument cluster (IC) receives the overdrive (O/D) off signal from the PCM over the high speed controller area network (HS-CAN) communication bus. When the O/D function is selected off, the PCM sends a message to the instrument cluster (IC) to illuminate the O/D off indicator. If the speed control message is missing or if the data is deemed invalid by the instrument cluster (IC) for more than 5 seconds, the instrument cluster (IC) sets DTC U0100 in continuous memory and defaults the O/D off indicator off.

NOTE: If DTC U0100 is set in the instrument cluster (IC), other observable symptoms may be an inoperative speedometer, tachometer or odometer.

This pinpoint test is intended to diagnose the following:

PINPOINT TEST W: THE O/D OFF INDICATOR IS NEVER/ALWAYS ON 

  1. W1 CHECK THE O/D OPERATION 
    • Test drive the vehicle while turning the O/D function on and off.
    • Does the O/D function operate correctly? 
    1. YES  : Go to  W2.
    2. NO  : REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
  2. W2 CARRY OUT THE INSTRUMENT CLUSTER (IC) INDICATOR LAMP CONTROL ACTIVE COMMAND USING THE SCAN TOOL 
    • Key in ON position.
    • Enter the following diagnostic mode on the diagnostic tool: Instrument Cluster (IC) DataLogger
    • Select the instrument cluster (IC) O/D off indicator (O_DOFFLMP) active command and command the O/D off indicator on and off. Observe the O/D off indicator.
    • Does the O/D off indicator illuminate when commanded on, and turn off when commanded off? 
    1. YES  : Go to  W3.
    2. NO  : Go to  W6.
  3. W3 RETRIEVE THE RECORDED DTCs FROM BOTH THE CONTINUOUS AND ON-DEMAND INSTRUMENT CLUSTER (IC) SELF-TESTS 
    • Check for recorded instrument cluster (IC) DTCs from the continuous and on-demand self-tests.
    • Is DTC U0100 recorded? 
    1. YES  : Go to Pinpoint Test AG  .
    2. NO  : Go to  W4.
  4. W4 RETRIEVE THE RECORDED DTCs FROM BOTH THE CONTINUOUS AND ON-DEMAND PCM SELF-TESTS 
    • Check for recorded PCM DTCs from the continuous and on-demand self-tests.
    • Are any PCM DTCs recorded? 
    1. YES  : REFER to the Introduction - Gasoline Engines article.
    2. NO  : Go to  W5.
  5. W5 CHECK FOR CORRECT PCM OPERATION 
    • Disconnect all the PCM connectors.
    • Check for:
      • corrosion
      • damaged pins
      • pushed-out pins
    • Connect all the PCM connectors and make sure they seat correctly.
    • Operate the system and determine if the concern is still present.
    • Is the concern still present? 
    1. YES  : INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS article. TEST the system for normal operation.
    2. NO  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
  6. W6 CHECK FOR CORRECT INSTRUMENT CLUSTER (IC) OPERATION 
    • Disconnect the instrument cluster (IC) connector.
    • Check for:
      • corrosion
      • damaged pins
      • pushed-out pins
    • Connect the instrument cluster (IC) connector and make sure it seats correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    1. YES  : INSTALL a new instrument cluster (IC). REFER to Instrument Cluster (IC) . TEST the system for normal operation.
    2. NO  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
scientia non olet · About LEMON Manuals