Pinpoint Test E: A Single Illumination Source Is Inoperative
- E1 CHECK VOLTAGE CIRCUITS TO THE INOPERATIVE ILLUMINATION SOURCE
- Disconnect: Inoperative Illumination Source.
- Turn the headlamp switch to the parking lamps ON position.
- Rotate the instrument panel dimmer switch to the full illumination position.
- Measure the voltage between the inoperative illumination source, harness side and ground. Refer to the following table for the correct vehicle, illumination source, connector, pin and circuit information.CONNECTOR-PIN SPECIFICATIONS
Vehicle Illumination Source Connector-Pin Circuit Expedition/ Navigator A4WD mode select switch C284-4 19 (LB/RD) Expedition Ash receptacle C2014-1 19 (LB/RD) Navigator Ash receptacle C2246-2 505 (GY/YE) Expedition/ Navigator Message center C253-1 19 (LB/RD) Expedition Adjustable pedal switch C2089-5 19 (LB/RD) Navigator Memory adjustable pedal switch C2235-2 19 (LB/RD) Expedition/ Navigator DVD player C9020-3 19 (LB/RD) Expedition/ Navigator Traction control switch C280-8 19 (LB/RD) Navigator Brake shift interlock C2096-4 235 (RD/BK) Navigator Clock C2016-2 19 (LB/RD) Navigator Window control switch C3193b-5 19 (LB/RD) Navigator LH rear door window switch C717-5 19 (LB/RD) Navigator RH rear door window switch C819-5 19 (LB/RD) Navigator Flip window switch C999-2 19 (LB/RD) Navigator Moon roof switch C9001-2 19 (LB/RD) Navigator Power liftgate switch C9000-2 19 (LB/RD) Navigator LH door lock switch C541-2 19 (LB/RD) Navigator RH door lock switch C632-2 19 (LB/RD) Navigator Memory set switch C503-3 19 (LB/RD) Navigator Headlamp switch C205b-5 19 (LB/RD) Navigator Headlamp switch C205C-1 19 (LB/RD) - Is the voltage greater than 10 volts?
- Yes : GO to E2.
- No : REPAIR the circuit in question. TEST the system for normal operation.
- E2 CHECK THE INOPERATIVE ILLUMINATION SOURCE GROUND
- Measure the resistance between the inoperative illumination source, harness side and ground. Refer to the following table for the correct vehicle, illumination source, connector, pin and circuit information CONNECTOR-PIN SPECIFICATIONS
Vehicle Illumination Source Connector-Pin Circuit Expedition/ Navigator A4WD mode select switch C284-1 57 (BK) Expedition Ash receptacle C2014-2 57 (BK) Navigator Ash receptacle C2246-2 57 (BK) Expedition/ Navigator Message center C253-4 57 (BK) Expedition Adjustable pedal switch C2089-4 57 (BK) Navigator Memory adjustable pedal switch C2235-1 57 (BK) Expedition/ Navigator DVD player C9020-14 694 (BK/LG) Expedition/ Navigator Traction control switch C280-7 57 (BK) Navigator Brake shift interlock C2096-6 57 (BK) Navigator Clock C2016-5 57 (BK) Navigator Window control switch C3193b-6 57 (BK) Navigator LH rear door window switch C717-1 57 (BK) Navigator RH rear door window switch C819-1 57 (BK) Navigator Flip window switch C999-1 57 (BK) Navigator Moon roof switch C9001-1 57 (BK) Navigator Power liftgate switch C9000-1 57 (BK) Navigator LH door lock switch C541-4 57 (BK) Navigator RH d4oor lock switch C632-1 57 (BK) Navigator Memory set switch C503-4 57 (BK) Navigator Headlamp switch C205b-4 57 (BK) Navigator Headlamp switch C205C-2 57 (BK) - Is the resistance less than 5 ohms?
- Yes : INSTALL a new component in question. TEST the system for normal operation.
- No : REPAIR the circuit in question. TEST the system for normal operation.
- Measure the resistance between the inoperative illumination source, harness side and ground. Refer to the following table for the correct vehicle, illumination source, connector, pin and circuit information