DTC P0016-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A [11/2021 - ]: Procedure

1. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC P0016-00 is output	A
   DTC P0016-00 and other DTCs are output	B

   HINT: 

   If any DTCs other than P0016-00 are output, troubleshoot those DTCs first.

Result: 

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2021 - 03/2023]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [03/2023 - 03/2024]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [03/2024 - ] 

Result: 

A 

See step  2

HINT: 

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

1. Start the engine.
2. Perform the Active Test. Check that the displacement angle varies.

   Powertrain > Engine > Active Test 

   Active Test Display
   Control the Intake VVT OCV Duty Ratio Bank 1

   Data List Display
   Intake VVT Change Angle Bank 1

   OK

   Displacement angle varies.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  6

Result: 

NG 

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA 

1. Inspect the cam timing oil control solenoid assembly (for intake side).

   Refer to INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE SIDE). Refer to  REMOVAL [11/2021 - ] 

Result: 

OK 

See step  5

1. Inspect the intake camshaft timing gear bolt assembly.

   Refer to ON-VEHICLE INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

Result: 

OK 

See step  6

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Turn the ignition switch off and wait for at least 30 seconds.
3. Start the engine and warm it up.
4. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
5. Read the pending DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0016-00 is output	B

Result: 

A 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2021 - ] 

Result: 

B 

See step  7

1. Replace the camshaft timing gear assembly.

   Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

   HINT: 

   Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

   Refer to INITIALIZATION [11/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Turn the ignition switch off and wait for at least 30 seconds.
3. Start the engine and warm it up.
4. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
5. Read the pending DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0016-00 is output	B

Result: 

A 

END 

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [11/2021 - ]