LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 81 (Can Communication System - Circuit Tests (5 Of 9)) >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Check Bus 3 Line [11/2021 - 03/2022] >> Procedure

Check Bus 3 Line [11/2021 - 03/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2025 Lexus NX 350, 2025 Lexus NX 250, 2024 Lexus NX 350, 2024 Lexus NX 250, and 2023 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1060084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-30 (CA3H) - D155-29 (CA3L) Cable disconnected from negative (-) battery terminal Below 70 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  55

    Result: 

    OK 

    See step  3

  3. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1060084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-30 (CA3H) - D155-29 (CA3L) Cable disconnected from negative (-) battery terminal 54 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  40

    Result: 

    OK 

    See step  4

  4. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064277Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-30 (CA3H) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D155-29 (CA3L) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  25

    Result: 

    OK 

    See step  5

  5. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064280Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-30 (CA3H) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D155-29 (CA3L) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  10

  6. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1063677Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-30 (CA3H) - D71-29 (CA3L) Cable disconnected from negative (-) battery terminal Below 70 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  55

    Result: 

    OK 

    See step  7

  7. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1063677Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-30 (CA3H) - D71-29 (CA3L) Cable disconnected from negative (-) battery terminal 54 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  40

    Result: 

    OK 

    See step  8

  8. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1065668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-30 (CA3H) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D71-29 (CA3L) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  25

    Result: 

    OK 

    See step  9

  9. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1065669Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-30 (CA3H) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D71-29 (CA3L) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  10

  10. CHECK FOR SHORT TO GND IN CAN MAIN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D97 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  24

    Result: 

    OK 

    See step  11

  11. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-16 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  19

    Result: 

    OK 

    See step  12

  12. CHECK FOR SHORT TO GND IN CAN BRANCH BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-13 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  20

    Result: 

    OK 

    See step  13

  13. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    Result: 

    B 

    See step  15

    Result: 

    A 

    See step  14

  14. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-15 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  21

    Result: 

    OK 

    See step  15

  15. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Active Noise Control System A
      w/o Active Noise Control System B

    Result: 

    B 

    See step  17

    Result: 

    A 

    See step  16

  16. CHECK FOR SHORT TO GND IN CAN BRANCH BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-14 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  22

    Result: 

    OK 

    See step  17

  17. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Digital Inner Mirror System A
      w/o Digital Inner Mirror System B

    Result: 

    B 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  18

  18. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-17 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  23

  19. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Disconnect the D22 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-16 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 

  20. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the D2 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-13 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 

  21. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Disconnect the D11 DCM (telematics transceiver) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-15 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 

  22. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Disconnect the D38 stereo component equalizer assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-14 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 

  23. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Disconnect the M4 inner rear view mirror assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-17 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE INNER REAR VIEW MIRROR ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 

  24. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D97-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  25. CHECK FOR SHORT TO +B IN CAN MAIN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D97 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  39

    Result: 

    OK 

    See step  26

  26. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-16 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  34

    Result: 

    OK 

    See step  27

  27. CHECK FOR SHORT TO +B IN CAN BRANCH BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-13 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  35

    Result: 

    OK 

    See step  28

  28. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    Result: 

    B 

    See step  30

    Result: 

    A 

    See step  29

  29. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-15 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  36

    Result: 

    OK 

    See step  30

  30. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Active Noise Control System A
      w/o Active Noise Control System B

    Result: 

    B 

    See step  32

    Result: 

    A 

    See step  31

  31. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-14 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  37

    Result: 

    OK 

    See step  32

  32. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Digital Inner Mirror System A
      w/o Digital Inner Mirror System B

    Result: 

    B 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  33

  33. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-17 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  38

  34. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Disconnect the D22 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-16 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 

  35. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the D2 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-13 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 

  36. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Disconnect the D11 DCM (telematics transceiver) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-15 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 

  37. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Disconnect the D38 stereo component equalizer assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-14 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 

  38. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Disconnect the M4 inner rear view mirror assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-17 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE INNER REAR VIEW MIRROR ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 

  39. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D97-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  40. CHECK FOR SHORT IN CAN MAIN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D97 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D97-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  54

    Result: 

    OK 

    See step  41

  41. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D97-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  49

    Result: 

    OK 

    See step  42

  42. CHECK FOR SHORT IN CAN BRANCH BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D97-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  50

    Result: 

    OK 

    See step  43

  43. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    Result: 

    B 

    See step  45

    Result: 

    A 

    See step  44

  44. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D97-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  51

    Result: 

    OK 

    See step  45

  45. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Active Noise Control System A
      w/o Active Noise Control System B

    Result: 

    B 

    See step  47

    Result: 

    A 

    See step  46

  46. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D97-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  52

    Result: 

    OK 

    See step  47

  47. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Digital Inner Mirror System A
      w/o Digital Inner Mirror System B

    Result: 

    B 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  48

  48. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D97-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  53

  49. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Disconnect the D22 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D97-16 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 

  50. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the D2 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-2 (CANH) - D97-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) 

  51. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 
    1. Disconnect the D11 DCM (telematics transceiver) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-4 (CANH) - D97-15 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - DCM (TELEMATICS TRANSCEIVER) 

  52. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 
    1. Disconnect the D38 stereo component equalizer assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-3 (CANH) - D97-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - STEREO COMPONENT EQUALIZER ASSEMBLY) 

  53. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 
    1. Disconnect the M4 inner rear view mirror assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-6 (CANH) - D97-17 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE INNER REAR VIEW MIRROR ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - INNER REAR VIEW MIRROR ASSEMBLY) 

  54. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D97-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  55. CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      W/O TELEMATICS TRANSCEIVER

      Tester Connection Condition Specified Condition
      D71-30 (CA3H) - D71-29 (CA3L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      W/ TELEMATICS TRANSCEIVER

      Tester Connection Condition Specified Condition
      D155-30 (CA3H) - D155-29 (CA3L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  56

  56. CHECK FOR OPEN IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Reconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Disconnect the D97 No. 9 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-1 (CANH) - D97-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

    Result: 

    OK 

    See step  57

  57. CHECK FOR OPEN IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D97-5 (CANH) - D97-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  58

  58. CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D97 No. 9 global CAN junction connector.
    2. Disconnect the D22 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D22-31 (CANH) - D22-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

scientia non olet · About LEMON Manuals