DTC C0500-1F: Left Front Wheel Speed Sensor Circuit Intermittent [11/2021 - ]: Procedure

Pre-procedure1

1. Remove the front speed sensor LH.

   HINT: 

   w/o AVS: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

   w/ AVS: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

   Procedure1

2. Check the front speed sensor LH.

   OK

   The front speed sensor LH tip is free of oil and foreign matter.

   HINT: 

   If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor LH, this DTC may be stored.

   Result

   Proceed to
   OK
   NG

   Post-procedure1

3. None

Result: 

NG 

See step  7

Result: 

OK 

See step  2

Pre-procedure1

1. Remove the component with the front speed sensor rotor LH.

   HINT: 

   Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

   Procedure1

2. Check the front speed sensor rotor LH.

   OK

   The front speed sensor rotor LH is free of oil and foreign matter.

   HINT: 

   • If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor rotor LH, this DTC may be stored.
   • The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

     If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.

   Result

   Proceed to
   OK
   NG

   Post-procedure1

3. None

Result: 

OK 

REPLACE FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH 

for front speed sensor LH (w/o AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor LH (w/ AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor rotor LH: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

Result: 

NG 

See step  3

1. Clean the front speed sensor rotor LH.
   NOTE:

   Do not use parts cleaner when cleaning the front speed sensor rotor LH.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

Pre-procedure1

1. None

   Procedure1

2. Clear the DTCs.

   Chassis > Brake/EPB > Clear DTCs 

   Result

   Proceed to
   NEXT

   Post-procedure1

3. Turn the ignition switch to off.

Result: 

NEXT 

See step  5

1. Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

   HINT: 

   Refer to SIGNAL CHECK [11/2021 - ]

   Chassis > Brake/EPB > Utility 

   Tester Display
   Signal Check

   OK

   Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

   HINT: 

   The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

   If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH 

for front speed sensor LH (w/o AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor LH (w/ AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor rotor LH: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

Result: 

OK 

See step  6

Pre-procedure1

1. Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.

   Procedure1

2. Check if the same DTC is output.

   Chassis > Brake/EPB > Trouble Codes 

   HINT: 

   The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

   If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.

   Result

   Result	Proceed to
   C0500-1F is not output	A
   C0500-1F is output	B

   Post-procedure1

3. None

Result: 

A 

END 

Result: 

B 

REPLACE FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH 

for front speed sensor LH (w/o AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor LH (w/ AVS): Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

for front speed sensor rotor LH: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

1. Clean the front speed sensor LH.
   NOTE:

   When cleaning the front speed sensor LH, make sure to clean the installation hole before installation.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

Pre-procedure1

1. None

   Procedure1

2. Clear the DTCs.

   Chassis > Brake/EPB > Clear DTCs 

   Result

   Proceed to
   NEXT

   Post-procedure1

3. Turn the ignition switch off.

Result: 

NEXT 

See step  9

1. Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

   HINT: 

   Refer to SIGNAL CHECK [11/2021 - ]

   Chassis > Brake/EPB > Utility 

   Tester Display
   Signal Check

   OK

   Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  2

Result: 

OK 

See step  10

Pre-procedure1

1. Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.

   Procedure1

2. Check if the same DTC is output.

   Chassis > Brake/EPB > Trouble Codes 

   Result

   Result	Proceed to
   C0500-1F is not output	A
   C0500-1F is output	B

   Post-procedure1

3. None

Result: 

A 

END 

Result: 

B 

See step  2