LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 39 (Engine Control System - Service Information) >> ACTIVE CONTROL ENGINE MOUNT (for Front Side) >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

    Refer to BEFORE DISCONNECTING BATTERY [11/2021 - ]
  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

  3. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 8 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  4. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 9 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 9 [03/2024 - ]

  5. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 10 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 10 [03/2024 - ]

  6. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 11 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 11 [03/2024 - ]

  7. DRAIN COOLANT (for Intercooler) 

    Refer to PROCEDURE - Step 4

  8. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 4

  9. REMOVE RADIATOR UPPER AIR GUIDE PLATE 

    Refer to PROCEDURE - Step 1 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 1 [03/2024 - ]

  10. REMOVE INLET AIR CLEANER ASSEMBLY 

    See step  4

  11. REMOVE AIR CLEANER ASSEMBLY 

    See step  5

  12. REMOVE INTAKE MANIFOLD WITH INTERCOOLER ASSEMBLY 

    Refer to REMOVAL [11/2021 - ]

  13. DISCONNECT NO. 1 RADIATOR HOSE 
    1. GTY1076154Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. DISCONNECT WATER BY-PASS HOSE ASSEMBLY 
    1. GTY1076156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. DISCONNECT WIRE HARNESS 
    1. GTY1076152Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. DISCONNECT VACUUM HOSE 
    1. GTY1076147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE FRONT ENGINE MOUNTING BRACKET 
    1. GTY1076224Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Wooden Block Placement Location - -
      1. Support the engine assembly with transaxle using a jack and wooden block.
      2. Remove the 4 bolts and front engine mounting bracket.
  18. REMOVE FRONT ENGINE MOUNTING INSULATOR 
    1. GTY1076143Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals