LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 120 (Can Communication System - Circuit Tests (8 Of 9)) >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Check Bus 6 Line [03/2023 - 03/2024] >> Procedure

Check Bus 6 Line [03/2023 - 03/2024]: Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2025 Lexus NX 350, 2025 Lexus NX 250, 2024 Lexus NX 350, 2024 Lexus NX 250, and 2023 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Telematics Transceiver (for TMC Made) A
      except Telematics Transceiver (for TMC Made) B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1060087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-31 (CA7H) - D155-32 (CA7L) Cable disconnected from negative (-) battery terminal Below 70 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  94

    Result: 

    OK 

    See step  3

  3. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1060087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-31 (CA7H) - D155-32 (CA7L) Cable disconnected from negative (-) battery terminal 54 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  66

    Result: 

    OK 

    See step  4

  4. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064303Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-31 (CA7H) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D155-32 (CA7L) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  38

    Result: 

    OK 

    See step  5

  5. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064322Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D155-31 (CA7H) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D155-32 (CA7L) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  10

  6. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1063703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-31 (CA7H) - D71-32 (CA7L) Cable disconnected from negative (-) battery terminal Below 70 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  94

    Result: 

    OK 

    See step  7

  7. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1063703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-31 (CA7H) - D71-32 (CA7L) Cable disconnected from negative (-) battery terminal 54 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  66

    Result: 

    OK 

    See step  8

  8. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064217Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-31 (CA7H) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D71-32 (CA7L) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  38

    Result: 

    OK 

    See step  9

  9. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1064215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-31 (CA7H) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D71-32 (CA7L) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  10

  10. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D158 No. 16 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  16

    Result: 

    OK 

    See step  11

  11. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-4 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-10 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  20

    Result: 

    OK 

    See step  12

  12. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Automatic Headlight Beam Level Control System A
      w/o Automatic Headlight Beam Level Control System B

    Result: 

    B 

    See step  15

    Result: 

    A 

    See step  13

  13. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-7 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  17

    Result: 

    OK 

    See step  14

  14. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-11 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  18

    Result: 

    OK 

    See step  15

  15. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-9 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 16 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  19

  16. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  17. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Disconnect the A49 headlight ECU sub-assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-7 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 

  18. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Disconnect the A50 headlight ECU sub-assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-11 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 

  19. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Disconnect the E33 outer mirror control ECU assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      D158-9 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 

  20. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the G165 No. 10 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-7 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  21

  21. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-4 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-10 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  27

    Result: 

    OK 

    See step  22

  22. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Adaptive Variable Suspension System A
      w/o Adaptive Variable Suspension System B

    Result: 

    B 

    See step  24

    Result: 

    A 

    See step  23

  23. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-8 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  25

    Result: 

    OK 

    See step  24

  24. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-9 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  26

  25. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Disconnect the G2 absorber control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-8 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE ABSORBER CONTROL ECU. Refer to  REMOVAL [03/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 

  26. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Disconnect the E11 outer mirror control ECU assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G165-9 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 

  27. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the G151 No. 13 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-3 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-14 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  28

  28. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-13 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  33

    Result: 

    OK 

    See step  29

  29. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-17 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  34

    Result: 

    OK 

    See step  30

  30. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for AWD A
      for 2WD B

    Result: 

    B 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  31

  31. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for A25A-FKS (Type A) A
      for T24A-FTS, for A25A-FKS (Type B) B

    Result: 

    B 

    See step  36

    Result: 

    A 

    See step  32

  32. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  35

  33. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Disconnect the G152 No. 1 CAN junction terminal connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-13 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 CAN JUNCTION TERMINAL 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 

  34. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Disconnect the G90 tire pressure warning ECU and receiver connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-17 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 

  35. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G93 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-12 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  36. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-16 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  37

  37. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G92 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - D66-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G151-16 (CANL) - D66-4 (CG)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  38. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D158 No. 16 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  44

    Result: 

    OK 

    See step  39

  39. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-4 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-10 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  48

    Result: 

    OK 

    See step  40

  40. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Automatic Headlight Beam Level Control System A
      w/o Automatic Headlight Beam Level Control System B

    Result: 

    B 

    See step  43

    Result: 

    A 

    See step  41

  41. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-7 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  45

    Result: 

    OK 

    See step  42

  42. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-11 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  46

    Result: 

    OK 

    See step  43

  43. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-9 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 16 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  47

  44. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  45. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Disconnect the A49 headlight ECU sub-assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-7 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 

  46. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Disconnect the A50 headlight ECU sub-assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-11 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 

  47. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Disconnect the E33 outer mirror control ECU assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D158-9 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 

  48. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the G165 No. 10 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-7 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  49

  49. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-4 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-10 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  55

    Result: 

    OK 

    See step  50

  50. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Adaptive Variable Suspension System A
      w/o Adaptive Variable Suspension System B

    Result: 

    B 

    See step  52

    Result: 

    A 

    See step  51

  51. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-8 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  53

    Result: 

    OK 

    See step  52

  52. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-9 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  54

  53. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Disconnect the G2 absorber control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-8 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE ABSORBER CONTROL ECU. Refer to  REMOVAL [03/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 

  54. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Disconnect the E11 outer mirror control ECU assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G165-9 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 

  55. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the G151 No. 13 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-3 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-14 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  56

  56. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-13 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  61

    Result: 

    OK 

    See step  57

  57. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-17 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  62

    Result: 

    OK 

    See step  58

  58. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for AWD A
      for 2WD B

    Result: 

    B 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  59

  59. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for A25A-FKS (Type A) A
      for T24A-FTS, for A25A-FKS (Type B) B

    Result: 

    B 

    See step  64

    Result: 

    A 

    See step  60

  60. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  63

  61. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Disconnect the G152 No. 1 CAN junction terminal connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-13 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 CAN JUNCTION TERMINAL 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 

  62. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Disconnect the G90 tire pressure warning ECU and receiver connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-17 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 

  63. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G93 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-12 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  64. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-16 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  65

  65. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G92 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - D66-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G151-16 (CANL) - D66-16 (BAT)

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  66. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D158 No. 16 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D158-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  72

    Result: 

    OK 

    See step  67

  67. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-4 (CANH) - D158-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  76

    Result: 

    OK 

    See step  68

  68. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Automatic Headlight Beam Level Control System A
      w/o Automatic Headlight Beam Level Control System B

    Result: 

    B 

    See step  71

    Result: 

    A 

    See step  69

  69. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D158-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  73

    Result: 

    OK 

    See step  70

  70. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D158-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  74

    Result: 

    OK 

    See step  71

  71. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D158-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 16 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  75

  72. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D158-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  73. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 
    1. Disconnect the A49 headlight ECU sub-assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-1 (CANH) - D158-7 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH) 

  74. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 
    1. Disconnect the A50 headlight ECU sub-assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-5 (CANH) - D158-11 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH) 

  75. CHECK FOR SHORT IN CAN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 
    1. Disconnect the E33 outer mirror control ECU assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-3 (CANH) - D158-9 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH) 

  76. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D158 No. 16 global CAN junction connector.
    2. Disconnect the G165 No. 10 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-1 (CANH) - G165-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  77

  77. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-4 (CANH) - G165-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  83

    Result: 

    OK 

    See step  78

  78. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Adaptive Variable Suspension System A
      w/o Adaptive Variable Suspension System B

    Result: 

    B 

    See step  80

    Result: 

    A 

    See step  79

  79. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - G165-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  81

    Result: 

    OK 

    See step  80

  80. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - G165-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  82

  81. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 
    1. Disconnect the G2 absorber control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-2 (CANH) - G165-8 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE ABSORBER CONTROL ECU. Refer to  REMOVAL [03/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - ABSORBER CONTROL ECU) 

  82. CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 
    1. Disconnect the E11 outer mirror control ECU assembly RH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-3 (CANH) - G165-9 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH) 

  83. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the G165 No. 10 global CAN junction connector.
    2. Disconnect the G151 No. 13 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-3 (CANH) - G151-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  84

  84. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - G151-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  89

    Result: 

    OK 

    See step  85

  85. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - G151-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    NG 

    See step  90

    Result: 

    OK 

    See step  86

  86. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for AWD A
      for 2WD B

    Result: 

    B 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    A 

    See step  87

  87. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for A25A-FKS (Type A) A
      for T24A-FTS, for A25A-FKS (Type B) B

    Result: 

    B 

    See step  92

    Result: 

    A 

    See step  88

  88. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - G151-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  91

  89. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Disconnect the G152 No. 1 CAN junction terminal connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - G151-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 CAN JUNCTION TERMINAL 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 

  90. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 
    1. Disconnect the G90 tire pressure warning ECU and receiver connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-6 (CANH) - G151-17 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER) 

  91. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G93 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-1 (CANH) - G151-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  92. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - G151-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  93

  93. CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 
    1. Disconnect the G92 4WD ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-5 (CANH) - G151-16 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE 4WD ECU ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2024] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - 4WD ECU ASSEMBLY) 

  94. CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      EXCEPT TELEMATICS TRANSCEIVER (FOR TMC MADE)

      Tester Connection Condition Specified Condition
      D71-31 (CA7H) - D71-32 (CA7L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      W/ TELEMATICS TRANSCEIVER (FOR TMC MADE)

      Tester Connection Condition Specified Condition
      D155-31 (CA7H) - D155-32 (CA7L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  95

  95. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Reconnect the D71 or D155 central gateway ECU (network gateway ECU) connector.
    2. Disconnect the D158 No. 16 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-6 (CANH) - D158-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

    Result: 

    OK 

    See step  96

  96. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 16 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D158-4 (CANH) - D158-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 16 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  97

  97. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D158 No. 16 global CAN junction connector.
    2. Disconnect the G165 No. 10 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-1 (CANH) - G165-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 16 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  98

  98. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G165-4 (CANH) - G165-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  99

  99. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the G165 No. 10 global CAN junction connector.
    2. Disconnect the G151 No. 13 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-3 (CANH) - G151-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  100

  100. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G151-2 (CANH) - G151-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  101

  101. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION TERMINAL - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the G151 No. 13 global CAN junction connector.
    2. Disconnect the G152 No. 1 CAN junction terminal.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G152-3 (CANH) - G152-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Result
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 CAN JUNCTION TERMINAL 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 13 GLOBAL CAN JUNCTION CONNECTOR) 

scientia non olet · About LEMON Manuals