LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 113 (Engine Intake / Exhaust System - Service Information) >> Exhaust Manifold >> Removal [03/2022 - ] >> Procedure

Removal [03/2022 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 250, 2024 Lexus NX 250, 2023 Lexus NX 250, and 2022 Lexus NX 250. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 1

  2. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
    1. GTY1080353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE HOOD TO FRONT FENDER SEAL LH 
  4. REMOVE HOOD TO FRONT FENDER SEAL RH 
  5. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 

    Refer to REMOVAL [11/2021 - ]

  6. REMOVE COWL VENTILATOR SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 7 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 7 [03/2024 - ]

  7. REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  8. REMOVE AIR FUEL RATIO SENSOR (for Sensor 1) 
    Refer to REMOVAL [11/2021 - ]
  9. REMOVE WIRING HARNESS CLAMP BRACKET 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    1. GTY1066270Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    1. Type A:
      GTY1080350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Type B:
      GTY1131593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. SEPARATE NO. 1 FRONT FLOOR HEAT INSULATOR 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    1. GTY1066269Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE MANIFOLD STAY 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    1. GTY1079974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst) 
    WARNING:
    • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    1. GTY1079829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Front Floor Heat Insulator *2 No. 1 Exhaust Manifold Heat Insulator
      *3 Exhaust Manifold (TWC: Front Catalyst) - -
      1. Remove the 7 nuts and separate the exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.
      2. Remove the No. 1 front floor heat insulator, No. 1 exhaust manifold heat insulator and exhaust manifold (TWC: Front Catalyst).
  14. REMOVE EXHAUST MANIFOLD TO HEAD GASKET 
    1. GTY1079995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR 
    1. Type A:
      GTY1080352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Type B:
      GTY1130059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals