LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Engine Mechanical System - Service Information (4 Of 4)) >> Engine Unit >> Installation [11/2021 - ] >> Procedure

Installation [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL WIRE HARNESS CLAMP BRACKET 
    1. GTY1078813Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 2 timing chain cover assembly with the bolt.

        Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

      2. Using an 8 mm socket wrench, install the wire harness clamp bracket to the crankshaft bearing cap with the bolt.

        Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  2. INSTALL CRANKSHAFT POSITION SENSOR 
    Refer to PROCEDURE - Step 1
  3. INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) 
    Refer to PROCEDURE - Step 1
  4. INSTALL KNOCK CONTROL SENSOR 
    Refer to PROCEDURE - Step 1
  5. INSTALL ENGINE COOLANT TEMPERATURE SENSOR (for Cylinder Head Side) 
    Refer to PROCEDURE - Step 1
  6. INSTALL HEATER WATER HOSE BRACKET 

    Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  7. INSTALL WATER BY-PASS GASKET 
    1. GTY1077731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw - -
      1. Install a new water by-pass gasket to the water by-pass pipe sub-assembly.
        NOTE:

        Make sure that the claws of the water by-pass gasket are toward the water by-pass pipe sub-assembly side.

  8. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY 

    Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  9. INSTALL WATER BY-PASS HOSE 
  10. INSTALL EXHAUST PIPE HEAT INSULATOR 
    Refer to PROCEDURE - Step 5
  11. INSTALL NO. 2 MANIFOLD STAY 

    Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

  12. INSTALL WATER INLET HOUSING 

    Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

  13. INSTALL WIRE HARNESS 
    1. GTY1078586Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using an 8 mm socket wrench, install the wire harness with bolt.

        Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

      2. Engage the 2 clamps.
      3. Connect the 4 connectors.
  14. INSTALL IGNITION COIL ASSEMBLY 
    Refer to PROCEDURE - Step 2 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 2 [03/2023 - ]
  15. INSTALL PORT FUEL INJECTOR ASSEMBLY 
    Refer to PROCEDURE - Step 1 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 1 [03/2023 - ]
  16. INSTALL NO. 5 ENGINE WIRE 
  17. INSTALL INJECTOR VIBRATION INSULATOR 
  18. INSTALL FUEL DELIVERY SPACER 
  19. INSTALL FUEL DELIVERY PIPE 
    Refer to PROCEDURE - Step 5 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 5 [03/2023 - ]
  20. INSTALL NO. 2 WATER BY-PASS PIPE 

    Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  21. INSTALL FUEL PUMP LIFTER ASSEMBLY 
    Refer to PROCEDURE - Step 1 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 1 [03/2023 - ]
  22. INSTALL FUEL PUMP SPACER GASKET 
  23. TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY 
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 3 [03/2023 - ]
  24. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 4 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 4 [03/2023 - ]
  25. INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY 
    Refer to PROCEDURE - Step 5 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 5 [03/2023 - ]
  26. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 6 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 6 [03/2023 - ]
  27. CONNECT FUEL TUBE SUB-ASSEMBLY 
    1. GTY1077675Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Connect the fuel tube sub-assembly to the fuel delivery pipe.

        Refer to PRECAUTION [11/2021 - ]

      2. Connect the fuel tube sub-assembly to the fuel (engine room side) pump assembly.

        Refer to PRECAUTION [11/2021 - ]

      3. Install the EFI fuel pipe clamp (fuel delivery pipe side) to the fuel tube connector.
  28. CONNECT WATER OUTLET STAY 

    Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  29. INSTALL TURBOCHARGER SUB-ASSEMBLY 
    1. Fig 1: Turbocharger Sub-Assembly Nuts Tightening Sequence
      GTY1081054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install a new exhaust manifold to head gasket.
      2. Install the turbocharger sub-assembly with the 4 nuts in the order shown in the illustration.

        Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

  30. INSTALL NO. 1 TURBO OIL OUTLET GASKET 
    1. GTY1078833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw - -
      1. Install a new No. 1 turbo oil outlet gasket to the No. 1 turbo oil pipe.
        NOTE:

        Make sure that the claws of the No. 1 turbo oil outlet gasket are toward the No. 1 turbo oil pipe side.

  31. INSTALL NO. 1 TURBO OIL PIPE 
    1. Fig 2: No. 1 Turbo Oil Pipe Union Bolt And Nuts Tightening Sequence
      GTY1080588Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Turbo Oil Inlet Gasket *2 Gasket
      Bolt Nut
      Oil Pipe Union Bolt - -
      1. Install a new turbo oil inlet gasket and gasket.

        HINT: 

        Face the straight part of the turbo oil inlet gasket toward the outside of the engine.

      2. Temporarily install the No. 1 turbo oil pipe with the 2 bolts, oil pipe union bolt and 2 nuts in the order shown in the illustration.
      3. Tighten the 2 bolts, oil pipe union bolt and 2 nuts in the order shown in the illustration.

        Bolt 

        Torque: 24 N.m (245 kgf/cm, 18 ft.lbf) 

        Oil Pipe Union Bolt 

        Torque: 35 N.m (357 kgf/cm, 26 ft.lbf) 

        Nut 

        Torque: 12 N.m (122 kgf/cm, 9 ft.lbf) 

  32. INSTALL MANIFOLD STAY 

    Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

  33. INSTALL NO. 1 HEAT INSULATOR BRACKET 

    Refer to PROCEDURE - Step 5

  34. CONNECT NO. 3 TURBO WATER HOSE 
    Refer to PROCEDURE - Step 6
  35. CONNECT NO. 2 TURBO WATER HOSE 
    Refer to PROCEDURE - Step 7
  36. INSTALL NO. 1 TURBO INSULATOR 

    Refer to PROCEDURE - Step 8

  37. INSTALL COMPRESSOR INLET ELBOW SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 11
  38. INSTALL VACUUM REGULATING VALVE ASSEMBLY 
    Refer to PROCEDURE - Step 1
  39. INSTALL CONVERTER WITH CATALYST ASSEMBLY 

    Refer to INSTALLATION [11/2021 - ]

  40. INSTALL WATER OUTLET GASKET 
    1. GTY1078960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw - -
      1. Install a new water outlet gasket to the front water by-pass joint.
        NOTE:

        Make sure that the claws of the water outlet gasket are toward the front water by-pass joint side.

  41. INSTALL FRONT WATER BY-PASS JOINT 

    Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  42. INSTALL WATER CONTROL VALVE 

    Refer to PROCEDURE - Step 1

  43. INSTALL INTAKE MANIFOLD WITH INTERCOOLER ASSEMBLY 
    Refer to PROCEDURE - Step 4
  44. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE 
    1. GTY1077687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Apply a light coat of engine oil to a new O-ring.
      2. Install the O-ring to the engine oil level dipstick guide.
      3. Using an 8 mm socket wrench, install the engine oil level dipstick guide to the intake manifold with the bolt.

        Torque: 10 N.m (102 kgf/cm, 89 in.lbf) 

      4. Install the engine oil level dipstick.
  45. CONNECT NO. 5 WATER BY-PASS HOSE 
  46. CONNECT NO. 4 WATER BY-PASS HOSE 
    Refer to PROCEDURE - Step 7
  47. CONNECT NO. 4 TURBO WATER HOSE 
    Refer to PROCEDURE - Step 9
  48. CONNECT NO. 3 WATER BY-PASS HOSE 
    Refer to PROCEDURE - Step 11
  49. CONNECT NO. 1 TURBO WATER HOSE 
    Refer to PROCEDURE - Step 13
  50. CONNECT NO. 2 FUEL VAPOR FEED HOSE 
  51. INSTALL AIR TUBE ASSEMBLY 
    Refer to PROCEDURE - Step 15
  52. CONNECT NO. 1 VENTILATION PRESSURE SENSOR HOSE 
  53. INSTALL PURGE VALVE (PURGE VSV) 

    Refer to PROCEDURE - Step 16

  54. INSTALL NO. 2 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  55. INSTALL DRIVE SHAFT BEARING BRACKET 

    Torque: 63.7 N.m (650 kgf/cm, 47 ft.lbf) 

scientia non olet · About LEMON Manuals