Caution / Notice / Hint
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear stabilizer bar removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR HEV MODEL)
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) Refer to WORK PROCEDURE [11/2021 - 03/2023] , or refer to WORK PROCEDURE [03/2023 - 03/2024] |
| Rear television camera assembly optical axis (Back camera position setting)*3 | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization*3 | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] | |
| Advanced Park | Refer to CALIBRATION [11/2021 - 03/2024] |
*1: Also necessary after performing a tire rotation.
*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*3: The vehicle height changes because of tire replacement.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR GASOLINE MODEL)
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) Refer to WORK PROCEDURE [11/2021 - 03/2023] , or refer to WORK PROCEDURE [03/2023 - 03/2024] |
| Rear television camera assembly optical axis (Back camera position setting)*3 | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization*3 | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] | |
| ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) | Dynamic Torque Control AWD System (for T24A-FTS, A25A-FKS (Type B)) | Refer to CALIBRATION [11/2021 - 03/2023] , or refer to CALIBRATION [03/2023 - ] |
*1: Also necessary after performing a tire rotation.
*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*3: The vehicle height changes because of tire replacement.
COMPONENTS (REMOVAL)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | REAR WHEEL | - | - | - | - |
| 2 | NO. 1 LOWER CONTROL ARM COVER LH | 48738B | - | - | - |
| 3 | NO. 1 LOWER CONTROL ARM COVER RH | 48737B | - | - | - |
| 4 | SEPARATE REAR STABILIZER LINK ASSEMBLY LH | 48840A | See step 4 | - | - |
| 5 | SEPARATE REAR STABILIZER LINK ASSEMBLY RH | 48830D | - | - | - |
| 6 | REAR STABILIZER BAR | 48812 | - | - | - |
| 7 | REMOVE REAR STABILIZER LINK ASSEMBLY LH | 48840A | See step 7 | - | - |
| 8 | REMOVE REAR STABILIZER LINK ASSEMBLY RH | 48830D | - | - | - |
| 9 | REAR LOWER STABILIZER BRACKET | 48835 | - | - | - |
| 10 | REAR NO. 1 STABILIZER BAR BRACKET | 48832A | - | - | - |
| 11 | REAR STABILIZER BUSHING | 48818 | - | - | - |