LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - Service Information >> Combination Meter >> Installation [11/2021 - ] >> Procedure

Installation [11/2021 - ]: Procedure

  1. INSTALL COMBINATION METER ASSEMBLY 
  2. INSTALL COMBINATION METER ASSEMBLY WITH INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Fig 1: Combination Meter Assembly With Instrument Cluster Finish Panel Sub-Assembly Screws Tightening Sequence
      GTY1069044Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A w/ Headup Display - -
      Install in this Direction (1) Install in this Direction (2)
      1. Connect each connector.
      2. Engage the clamp.
      3. Engage the 2 clips as shown in the illustration.
      4. Install the combination meter assembly with instrument cluster finish panel sub-assembly with the 4 screws.

        HINT: 

        Install the screws in the order shown in the illustration.

      5. Engage the 2 guides and 4 clips as shown in the illustration.
  3. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET 

    Refer to PROCEDURE - Step 5

  4. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY 
  5. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
  6. INSTALL METER HOOD SUB-ASSEMBLY 
  7. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 
  8. INSTALL LOWER INSTRUMENT FINISH PANEL SUB-ASSEMBLY 
  9. INSTALL NO. 1 INSTRUMENT SIDE PANEL 
  10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
    Refer to PROCEDURE - Step 1 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 1 [03/2022 - ]
  11. INSTALL INSTRUMENT PANEL FINISH PANEL 
  12. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
  13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH 
  14. INSTALL DOOR SCUFF PLATE ASSEMBLY LH 
  15. INSTALL CONSOLE PANEL 
  16. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY 
  17. INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH 
  18. INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH 
  19. INSTALL CONSOLE BOX HOLE COVER 
  20. INSTALL SHIFTING HOLE COVER ASSEMBLY 
  21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY 
    1. for UA81F:

      Refer to PROCEDURE - Step 1

    2. for UB80E / UB80F:

      Refer to PROCEDURE - Step 1

    3. for P810:

      Refer to PROCEDURE - Step 1
  22. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 28 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 28 [03/2022 - ]
  23. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL 
  24. UPDATE ECU SECURITY KEY 

    Refer to UPDATE ECU SECURITY KEY [11/2021 - ]

  25. PERFORM REGISTRATION (w/ Headup Display) 

    HINT: 

    When replacing the combination meter assembly, perform registration.

    Refer to REGISTRATION [11/2021 - ]

  26. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column) 
    Refer to PROCEDURE - Step 17 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 17 [03/2024 - ]
scientia non olet · About LEMON Manuals