Installation [11/2021 - 03/2024]: Procedure

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Slot	-	-
   	Outside of the Vehicle	-	-

   1. Align the slot on end of the shock rod of the front shock absorber assembly as shown in the illustration.
      NOTE:

      Be sure to install the part so that the slot on the front suspension support sub-assembly and the slot on the shock rod end are aligned.

2. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Front Shock Absorber Assembly	*2	Shock Absorber Outer Shell
   *a	Turn	*b	Hold
   *c	Fixing Nut	*d	Bolt

   1. Install SST (09727-58100) and SST (09727-58130) to the front shock absorber assembly.
      • SST: 09727-58100 
      • SST: 09727-58130 
      • SST: 09727-58010 
        1. 09727-58030
      NOTE:

      Apply molybdenum grease to the bolt (area with diagonal lines) of SST (09727-58010).

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Application Area

   2. Install SST (09727-58030) to the end of the shock rod of the front shock absorber assembly. [#1]
   3. Install SST (09727-58010) to the front shock absorber assembly. [#2]
      NOTE:

      Take due care when installing SST (09727-58010) to ensure the shock rod is not damaged.

   4. Secure the SST (09727-58010) bolt and SST (09727-58030) with the fixing nut. [#3]
   5. After securing the SST (09727-58010) bolt, rotate the nut clockwise. [#4]

      HINT: 

      Extend the shock rod to its maximum length to install SST (09727-58100) and SST (09727-58130).

   6. Using a piece of cloth, etc., clean the shock rod and remove any foreign matter and oil.
      NOTE:

      Thoroughly clean the shock rod to prevent damage to the shock rod due to contact of foreign matter.

   7. Clean the surface of SST (09727-58130) to which the front shock absorber assembly is installed and remove any foreign matter and oil.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a	Installation Surface

      NOTE:

      Thoroughly clean the installation surface to prevent damage to the shock rod due to contact of foreign matter.

   8. Using a long ball hexagon 5, install SST (09727-58100) and SST (09727-58130) to the shock rod. [#5]
      NOTE:

      Before installing, check the position of the slot on end of the shock rod.

      HINT: 

      Install SST (09727-58100) and SST (09727-58130) to the base of the shock rod and check that SST (09727-58100) and SST (09727-58130) are securing the shock rod.

   9. After securing the SST (09727-58010) bolt, rotate the nut counterclockwise.
   10. Check that the shock rod and SST (09727-58030) have become free before releasing the fixing nut and removing SST (09727-58010) from the end of the shock rod.
       NOTE:

       Take due care when removing SST (09727-58010) to ensure the shock rod is not damaged.

   11. Remove SST (09727-58030) from the end of the shock rod.
   12. Using a piece of cloth, etc., clean the end of the shock rod threads and remove any foreign matter and oil.

NOTE: When installing the front lower coil spring insulator, insert the positioning pin of the spring seat into the hole of the front lower coil spring insulator.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Positioning Pin

   -

   -

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   1. Secure SST in a vise.
      • SST: 09727-00051 
      • SST: 09727-30022 
        1. 09727-00010
        2. 09727-00031
   2. Attach the hooks of each SST arm across the diameter of the coil spring.
      WARNING:

      • Make sure that the hooks are securely attached to the coil spring.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
      • Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
      • Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
   3. Install the stopper pins to the hooks of SST.
      WARNING:

      • Make sure that the stopper pins are installed securely.
      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   4. Using SST, compress the coil spring.
      WARNING:

      • If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
      • Do not compress the coil spring to the point where the coils touch each other.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
      • Do not use an impact wrench.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.
      • If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      • If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.
      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
      • SST: 09727-00110 

2. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Depression

   -

   -

   1. Align the end of the front coil spring with the flange of the front lower coil spring insulator and install the front coil spring.
      NOTE:

      Make sure to fit the end of the front coil spring that has the larger diameter into the depression of the front lower coil spring insulator.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Strut Mounting Bearing	-	-
   *a	Top End of the Front No. 1 Shock Absorber Dust Cover	-	-

   1. Install the strut mounting bearing to the front No. 1 shock absorber dust cover.
      NOTE:

      Make sure that the top end of the front No. 1 shock absorber dust cover and strut mounting bearing are securely attached.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Stud Bolt of Front Suspension Support Sub-assembly	*b	Front Shock Absorber Lower Bracket
   *c	Slot	*d	0° +/- 3°
   *e	Alignment Mark of Strut Mounting Bearing	*f	Guide Line of Front Suspension Support Sub-assembly
   *g	15°	*h	Arrow of Front No. 1 Shock Absorber Dust Cover
   	Outside of the Vehicle	-	-

   1. As shown in the illustration, align the stud bolt of the front suspension support sub-assembly with the shock absorber lower bracket and install them to the front shock absorber assembly.
      NOTE:

      • Align the notch of the front suspension support sub-assembly with the slot at the end of the shock rod and install.
      • When installing the front suspension support sub-assembly, make sure the stud bolt of the front suspension support sub-assembly is within +/- 3° of the absorber lower bracket.
   2. As shown in the illustration, align the alignment mark of the strut mounting bearing and guide line of the front suspension support sub-assembly.
      NOTE:

      When installing the strut mounting bearing, make sure to align within +/- 15° of the guide line of the front suspension support sub-assembly.

   3. As shown in the illustration, align the alignment mark of the strut mounting bearing and arrow of the No. 1 front shock absorber dust cover.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Cloth, etc.

   *b

   Shock Rod

   1. Temporarily tighten a new front support to front shock absorber nut.
   2. Remove SST from the front coil spring.
      NOTE:

      Do not use an impact wrench. It will damage SST.

   3. Fold back the front No. 1 shock absorber dust cover and then use a long ball hexagon 5 to remove SST (09727-58100) and SST (09727-58130) from the front shock absorber assembly.
      NOTE:

      • Thoroughly remove SST (09727-58100) and SST (09727-58130).
      • Check that front No. 1 shock absorber dust cover is not excessively deformed or crushed.
   4. Using a piece of cloth, etc., clean the shock rod of the front shock absorber assembly and remove any foreign matter and oil.
      NOTE:

      Thoroughly clean the shock rod to prevent damage to the front shock absorber assembly due to contact of foreign matter.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Front No. 1 Shock Absorber Dust Cover	-	-
   *a	Claw	-	-

   1. Connect the end of the front No. 1 shock absorber dust cover with the claws of the front shock absorber assembly.
      NOTE:

      • Make sure that the end of the front No. 1 shock absorber dust cover is securely attached to the claws of the front shock absorber assembly.
      • Make sure there is no excessive damage to the bellows of the front No. 1 shock absorber dust cover.
      • Do not allow oil, grease, etc., to contact the front No. 1 shock absorber dust cover.
      • If there is oil or grease on the insulator, wipe clean with a cloth. Do not use an alcohol based cleaner.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   1. Install the front shock absorber with coil spring (upper side) with the 3 nuts.

      Torque: 50 N.m (510 kgf/cm, 37 ft.lbf) 

   2. Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

      Torque: 290 N.m (2957 kgf/cm, 214 ft.lbf) 

      NOTE:

      • When installing the nuts, keep the bolts from rotating.
      • Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.

NOTE: Perform this step only when the front shock absorber with coil spring has been disassembled.

Torque: 47 N.m (479 kgf/cm, 35 ft.lbf) 

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1

   Hook

   -

   -

   1. Engage the 2 hooks to install the front speed sensor clamp bracket.
      NOTE:

      Do not twist the front speed sensor when installing it.

   2. Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

      Torque: 18.8 N.m (192 kgf/cm, 14 ft.lbf) 

   3. Engage the clamp.
      NOTE:

      Do not twist the front speed sensor when installing it.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1

   Hook

   -

   -

   1. Engage the 2 hooks to install the front skid control sensor wire clamp bracket.
      NOTE:

      Do not twist the front skid control sensor wire when installing it.

   2. Install the front skid control sensor wire and front flexible hose to the front shock absorber assembly with the 2 bolts.

      Torque: 18.8 N.m (192 kgf/cm, 14 ft.lbf) 

      NOTE:

      Do not twist the front skid control sensor wire or front flexible hose when installing them.

   3. Connect the front speed sensor wire connector to the sensor bracket.
   4. Connect the AVS connector to the absorber control actuator.

Torque: 74 N.m (755 kgf/cm, 55 ft.lbf) 

HINT: 

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *A	for T24A-FTS	-	-
   	Install in this Direction	-	-

   Nut (A) 

   Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

   Bolt (B) 

   Torque: 5.5 N.m (56 kgf/cm, 49 in.lbf) 

   Nut (C) (for T24A-FTS) 

   Torque: 19 N.m (194 kgf/cm, 14 ft.lbf) 

Refer to INSTALLATION [11/2021 - ]

Refer to INSTALLATION [11/2021 - 03/2023] , or refer to INSTALLATION [03/2023 - 03/2024]

Refer to ADJUSTMENT [11/2021 - ]