LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 57 (Automatic Transaxle System - Service Information (1 Of 2)) >> Oil Cooler >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 8 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 9 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 9 [03/2024 - ]

  3. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 10 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 10 [03/2024 - ]

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 11 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 11 [03/2024 - ]

  5. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 12 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 12 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 12 [03/2024 - ]

  6. REMOVE SUSPENSION TOWER DAMPER (w/ Damper) 
    Refer to PROCEDURE - Step 4
  7. REMOVE RADIATOR UPPER AIR GUIDE PLATE 

    Refer to PROCEDURE - Step 1 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 1 [03/2024 - ]

  8. REMOVE INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 4

  9. REMOVE AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 5

  10. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 4

  11. DRAIN AUTOMATIC TRANSAXLE FLUID 
    1. GTY1061635Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Transmission Oil Filler Tube - -
      1. Remove the refill plug and gasket from the automatic transaxle case sub-assembly.
      2. Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.
      3. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.
      4. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

        Torque: 1.7 N.m (17 kgf/cm, 15 in.lbf) 

      5. Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

        HINT: 

        Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

      6. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

        HINT: 

        Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

  12. SEPARATE ENGINE WIRE 
    1. GTY1062736Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP 
    1. GTY1062708Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. DISCONNECT WATER BY-PASS HOSE ASSEMBLY 
    HINT: 
    Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.
    1. GTY1063135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. DISCONNECT INLET NO. 1 OIL COOLER HOSE 
    HINT: 
    Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and transmission oil cooler.
    1. GTY1062710Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE 
    HINT: 
    Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and transmission oil cooler.
    1. GTY1062700Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE TRANSMISSION OIL (ATF WARMER) COOLER 
    HINT: 
    Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.
    1. GTY1062701Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals