Caution / Notice / Hint
WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Replacement of ECM | Update ECU security key | Vehicle Control History (RoB) are stored | Refer to UPDATE ECU SECURITY KEY [11/2021 - ] |
| Perform Vehicle Identification Number (VIN) registration | DTC is output | Refer to REGISTRATION [11/2021 - ] | |
|
Inspection after repair |
|
Refer to INITIALIZATION [11/2021 - ] |
| Replacement of inverter with converter assembly | Resolver learning |
|
Refer to UTILITY [11/2021 - ] |
| Replacement of hybrid vehicle transaxle assembly |
|
||
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below Refer to WORK PROCEDURE [11/2021 - 03/2023] , or refer to WORK PROCEDURE [03/2023 - 03/2024] , or refer to WORK PROCEDURE [03/2024 - ] |
| Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] | ||
| Wheel alignment adjustment | Perform "Calibration" |
|
Refer to RESET MEMORY / CALIBRATION [11/2021 - ] |
| Steering intermediate shaft assembly*4 | Automatic rack centering | - | Refer to AUTOMATIC RACK CENTERING [11/2021 - ] |
| Replacement of front bumper assembly*1 | Front television camera view adjustment | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] |
| Advanced Park | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] | ||
| Suspension parts | Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [11/2021 - 03/2024] , or refer to CALIBRATION [03/2024 - ] | ||
| Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [11/2021 - 03/2022] , or refer to INITIALIZATION [03/2022 - ] |
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
*2: Also necessary after performing a tire rotation.
*3: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*4: If matchmarks were not placed when removing parts related to steering operation, perform automatic rack centering.
NOTE:
- This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Refer to PRECAUTION [11/2021 - ]
- To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
LEARNING COMPLETES WHEN VEHICLE IS DRIVEN
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| Lighting System (EXT) | Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. | Refer to INITIALIZATION [11/2021 - ] |
| Front Camera System | ||
| Adaptive High Beam System |
LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
E-latch System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. | Refer to INITIALIZATION [11/2021 - ] |
| Power Back Door System | Reset back door close position | Refer to INITIALIZATION [11/2021 - ] |
| Air Conditioning System | After the ignition switch is turned to ON, the servo motor standard position is recognized. | - |
COMPONENTS (REMOVAL)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | TIMING CHAIN COVER ASSEMBLY | 11310 | - | - | - |
| 2 | NO. 2 OIL PAN SUB-ASSEMBLY | 12102A | See step 2 | - | - |
| 3 | OIL STRAINER SUB-ASSEMBLY | 15104 | See step 3 | - | - |
| 4 | ENGINE OIL LEVEL SENSOR | 89491 | See step 4 | - | - |
| 5 | OIL PUMP BRACKET | 15167 | - | - | - |
| 6 | ENGINE BALANCER ASSEMBLY | 13620B | See step 6 | - | - |
| 7 | OIL PUMP ASSEMBLY | 15100 | - | - | - |
| 8 | STIFFENING CRANKCASE ASSEMBLY | 11420 | See step 8 | - | - |
| • | Non-reusable part | - | - |