LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> TX 350 Base, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 84 (Hybrid Control System - Diagnostic Codes (5 Of 5) & Circuit Tests) >> HYBRID CONTROL SYSTEM (for 1Motor-HEV Model) >> TRAIL Switch Circuit [09/2023 - ] >> Procedure

TRAIL Switch Circuit [09/2023 - ]: Procedure

WARNING: This page is about a different car, the 2024 Lexus TX 500h. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING GTS (CAN BUS CHECK) 
    1. Check the CAN Bus Check.

      CAN Bus Check 

      Result

      Result Proceed to
      All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
      None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B
    2. Turn the ignition switch off.

    Result: 

    B 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2023 - ] 

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (HEALTH CHECK) 
    1. Check for DTCs.

      Result

      Result Proceed to
      No DTCs are output. A
      DTCs are output. B
    2. Turn the ignition switch off.

    Result: 

    B 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2023 - ] 

    Result: 

    A 

    See step  3

  3. READ VALUE USING GTS (AUTO LSD SWITCH) 
    1. Read the value displayed on the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display Measurement Item Range Normal Condition
      Auto LSD Switch TRAIL switch condition ON or OFF TRAIL mode switch being pushed and held:
      ON
      TRAIL mode switch not operated:
      OFF

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Auto LSD Switch

      Result

      Result Proceed to
      The tester display changes according to the TRAIL mode switch operation. A
      The tester display does not change according to the TRAIL mode switch operation. B
    2. Turn the ignition switch off.

    Result: 

    A 

    GO TO PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2023 - ] 

    Result: 

    B 

    See step  4

  4. INSPECT TRAIL MODE SWITCH 

    Refer to INSPECTION [09/2023 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE TRAIL MODE SWITCH. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH - BODY GROUND) 
    1. Disconnect the TRAIL mode switch (electric parking brake switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D22-7 (E) - Body ground Always Below 1 Ω
    3. Reconnect the TRAIL mode switch (electric parking brake switch assembly) connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - TRAIL MODE SWITCH) 
    1. Disconnect the hybrid vehicle control ECU assembly connector.
    2. Disconnect the TRAIL mode switch connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D44-19 (ALSD) - D22-6 (B) Always Below 1 Ω
      D44-19 (ALSD) or D22-6 (B) - Body ground Always 10 kΩ or higher
    4. Reconnect the TRAIL mode switch connector.
    5. Reconnect the hybrid vehicle control ECU assembly connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals