LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> TX 350 Base, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 112 (Can Communication System - Circuit Tests (3 Of 4)) >> CAN COMMUNICATION SYSTEM (for 1Motor-HEV Model) >> Check Bus 2 Line [09/2023 - ] >> Procedure

Check Bus 2 Line [09/2023 - ]: Procedure

WARNING: This page is about a different car, the 2024 Lexus TX 500h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1238597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D48-26 (CA4H) - D48-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  59

    Result: 

    OK 

    See step  2

  2. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1238597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D48-26 (CA4H) - D48-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  41

    Result: 

    OK 

    See step  3

  3. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1238597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D48-26 (CA4H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D48-25 (CA4L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  23

    Result: 

    OK 

    See step  4

  4. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1238597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D48-26 (CA4H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D48-25 (CA4L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  5

  5. CHECK FOR SHORT TO GND IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the J72 EV motor control inverter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      J72-13 (CA5L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  6

  6. CHECK FOR SHORT TO GND IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-14 (CA6H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      J72-15 (CA6L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE EV MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    See step  8

  7. CHECK FOR SHORT TO GND IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D48 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      J72-13 (CA5L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  8. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Disconnect the D72 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-3 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D72-10 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 

    Result: 

    OK 

    See step  9

  9. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-1 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D72-8 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  12

    Result: 

    OK 

    See step  10

  10. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D72-12 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  11

  11. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Disconnect the D25 transmission floor shift assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D72-12 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 

  12. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the D71 No. 8 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-5 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D71-11 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  13

  13. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-3 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D71-9 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  16

    Result: 

    OK 

    See step  14

  14. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D71-10 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  15

  15. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Disconnect the D44 hybrid vehicle control ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      D71-10 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 

  16. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the B66 No. 3 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-3 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B66-7 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  17

  17. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-1 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B66-5 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  20

    Result: 

    OK 

    See step  18

  18. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B66-6 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  19

  19. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Disconnect the C25 TCM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B66-6 (CANL) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TCM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 

  20. CHECK FOR SHORT TO GND IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the C46 hybrid motor control inverter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-32 (CA1H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      C46-33 (CA1L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  21

  21. CHECK FOR SHORT TO GND IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      C46-34 (CA2L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  22

  22. CHECK FOR SHORT TO GND IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Disconnect the B77 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      C46-34 (CA2L) - Body ground

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 

  23. CHECK FOR SHORT TO +B IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the J72 EV motor control inverter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      J72-13 (CA5L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  25

    Result: 

    OK 

    See step  24

  24. CHECK FOR SHORT TO +B IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-14 (CA6H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      J72-15 (CA6L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE EV MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    See step  26

  25. CHECK FOR SHORT TO +B IN CAN BUS LINE (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D48 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      J72-13 (CA5L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  26. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Disconnect the D72 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-3 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D72-10 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 

    Result: 

    OK 

    See step  27

  27. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-1 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D72-8 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  30

    Result: 

    OK 

    See step  28

  28. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D72-12 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  29

  29. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Disconnect the D25 transmission floor shift assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D72-12 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 

  30. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the D71 No. 8 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-5 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D71-11 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  31

  31. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-3 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D71-9 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  34

    Result: 

    OK 

    See step  32

  32. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D71-10 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  33

  33. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Disconnect the D44 hybrid vehicle control ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      D71-10 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 

  34. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the B66 No. 3 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-3 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      B66-7 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  35

  35. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-1 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      B66-5 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  38

    Result: 

    OK 

    See step  36

  36. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      B66-6 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  37

  37. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Disconnect the C25 TCM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      B66-6 (CANL) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TCM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 

  38. CHECK FOR SHORT TO +B IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the C46 hybrid motor control inverter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-32 (CA1H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      C46-33 (CA1L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  39

  39. CHECK FOR SHORT TO +B IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      C46-34 (CA2L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  40

  40. CHECK FOR SHORT TO +B IN CAN BUS LINE (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Disconnect the B77 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - Battery positive terminal Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      C46-34 (CA2L) - Battery positive terminal

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 

  41. CHECK FOR SHORT IN CAN BUS LINES (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the J72 EV motor control inverter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - J72-13 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  43

    Result: 

    OK 

    See step  42

  42. CHECK FOR SHORT IN CAN BUS LINES (EV MOTOR CONTROL INVERTER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-14 (CA6H) - J72-15 (CA6L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE EV MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    See step  44

  43. CHECK FOR SHORT IN CAN BUS LINES (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D48 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - J72-13 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  44. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Reconnect the J72 EV motor control inverter assembly connector.
    2. Disconnect the D72 No. 9 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-3 (CANH) - D72-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 

    Result: 

    OK 

    See step  45

  45. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-1 (CANH) - D72-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  48

    Result: 

    OK 

    See step  46

  46. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - D72-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  47

  47. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Disconnect the D25 transmission floor shift assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-5 (CANH) - D72-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY) 

  48. CHECK FOR SHORT IN CAN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D72 No. 9 global CAN junction connector.
    2. Disconnect the D71 No. 8 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-5 (CANH) - D71-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  49

  49. CHECK FOR SHORT IN CAN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-3 (CANH) - D71-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  52

    Result: 

    OK 

    See step  50

  50. CHECK FOR SHORT IN CAN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - D71-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  51

  51. CHECK FOR SHORT IN CAN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 
    1. Disconnect the D44 hybrid vehicle control ECU assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-4 (CANH) - D71-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 

  52. CHECK FOR SHORT IN CAN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D71 No. 8 global CAN junction connector.
    2. Disconnect the B66 No. 3 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-3 (CANH) - B66-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  53

  53. CHECK FOR SHORT IN CAN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-1 (CANH) - B66-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  56

    Result: 

    OK 

    See step  54

  54. CHECK FOR SHORT IN CAN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - B66-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  55

  55. CHECK FOR SHORT IN CAN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 
    1. Disconnect the C25 TCM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-2 (CANH) - B66-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TCM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - TCM) 

  56. CHECK FOR SHORT IN CAN BUS LINES (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the B66 No. 3 global CAN junction connector.
    2. Disconnect the C46 hybrid motor control inverter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-32 (CA1H) - C46-33 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  57

  57. CHECK FOR SHORT IN CAN BUS LINES (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - C46-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  58

  58. CHECK FOR SHORT IN CAN BUS LINES (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Disconnect the B77 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - C46-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 

  59. CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the D48 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D48-26 (CA4H) - D48-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  60

  60. CHECK FOR OPEN IN CAN MAIN BUS LINES (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Reconnect the D48 central gateway ECU (network gateway ECU) connector.
    2. Disconnect the J72 EV motor control inverter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-12 (CA5H) - J72-13 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (EV MOTOR CONTROL INVERTER ASSEMBLY - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

    Result: 

    OK 

    See step  61

  61. CHECK FOR OPEN IN CAN MAIN BUS LINES (EV MOTOR CONTROL INVERTER ASSEMBLY - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J72-14 (CA6H) - J72-15 (CA6L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE EV MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - 12/2023]  , or refer to  REMOVAL [12/2023 - ] 

    Result: 

    NG 

    See step  62

  62. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Reconnect the J72 EV motor control inverter assembly connector.
    2. Disconnect the D72 No. 9 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-3 (CANH) - D72-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - EV MOTOR CONTROL INVERTER ASSEMBLY) 

    Result: 

    OK 

    See step  63

  63. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D72-1 (CANH) - D72-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  64

  64. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D72 No. 9 global CAN junction connector.
    2. Disconnect the D71 No. 8 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-5 (CANH) - D71-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  65

  65. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 8 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D71-3 (CANH) - D71-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 8 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  66

  66. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the D71 No. 8 global CAN junction connector.
    2. Disconnect the B66 No. 3 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-3 (CANH) - B66-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 8 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  67

  67. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B66-1 (CANH) - B66-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  68

  68. CHECK FOR OPEN IN CAN MAIN BUS LINES (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Reconnect the B66 No. 3 global CAN junction connector.
    2. Disconnect the C46 hybrid motor control inverter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-32 (CA1H) - C46-33 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - NO. 3 GLOBAL CAN JUNCTION CONNECTOR) 

    Result: 

    OK 

    See step  69

  69. CHECK FOR OPEN IN CAN MAIN BUS LINES (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C46-35 (CA2H) - C46-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    See step  70

  70. CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM) 
    1. Reconnect the C46 hybrid motor control inverter assembly connector.
    2. Disconnect the B77 ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B77-26 (CFDH) - B77-25 (CFDL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [09/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - HYBRID MOTOR CONTROL INVERTER ASSEMBLY) 

scientia non olet · About LEMON Manuals