DTC P3190-00: Poor Engine Power; DTC P3191-00: Engine does not Start [09/2023 - ]: Procedure

1. Check for DTCs and Freeze Frame Data and write them down.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   P3190-00, P3191-00 or P3193-00 and other DTCs are output	A
   Only P3190-00 or P3191-00 is output	B
   Only P3193-00 is output	C

   HINT: 

   If any SFI system DTCs other than DTC P3190-00, P3191-00 or P3193-00 are output, perform troubleshooting for those DTCs first.

Result: 

A 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2023 - ] 

Result: 

C 

GO TO DTC P3193-00. Refer to  DTC P3193-00: Fuel Run Out [09/2023 - ]  

Result: 

B 

See step  2

1. Check the amount of fuel remaining.

   OK

   There is enough fuel.

   HINT: 

   • DTCs P3190-00, P3191-00 and/or P3193-00 may be output if the vehicle ran out of fuel in the past.
   • If not enough fuel is added, DTC P3190-00, P3191-00 or P3193-00 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning turns off.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REFILL FUEL 

Result: 

OK 

See step  3

Pre-procedure1

• None

• Clear the DTCs.

  Powertrain > Engine > Clear DTCs 

  Result

  Proceed to
  NEXT

Post-procedure1

• Turn the ignition switch off and wait for at least 30 seconds.

Result: 

NEXT 

See step  4

except Mexico Models 

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

for Mexico Models 

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Check the PCV hose connections.
2. Check the PCV valve.

   Refer to INSPECTION [09/2023 - ]

   OK

   PCV hose and PCV valve are connected correctly and are not damaged.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE PCV VALVE OR HOSE 

Result: 

OK 

See step  5

1. Check the intake system for vacuum leaks.

   Refer to ON-VEHICLE INSPECTION [09/2023 - ]

   OK

   No leaks from intake system.

   HINT: 

   Perform "Inspection After Repair" after repairing or replacing the intake system.

   Refer to INITIALIZATION [09/2023 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE INTAKE SYSTEM 

Result: 

OK 

See step  6

OK

Unusual noise and vibration do not occur.

Result

Result: 

NG 

REPAIR OR REPLACE MALFUNCTIONING PARTS 

Result: 

OK 

See step  7

Refer to ON-VEHICLE INSPECTION [09/2023 - ]

Result

Result: 

NG 

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE). Refer to  REMOVAL [09/2023 - ] 

Result: 

OK 

See step  8

Refer to INSPECTION [09/2023 - ]

Result

Result: 

NG 

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY). Refer to  REMOVAL [09/2023 - ] 

Result: 

OK 

See step  9

1. Inspect the mass air flow meter sub-assembly, referring to On-vehicle Inspection for Mass Air Flow Meter.

   Refer to ON-VEHICLE INSPECTION [09/2023 - ]

2. Inspect the mass air flow meter sub-assembly, referring to Inspection for Mass Air Flow Meter.

   Refer to INSPECTION [09/2023 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY. Refer to  REMOVAL [09/2023 - ] 

Result: 

OK 

See step  10

Refer to INSPECTION [09/2023 - ]

Result

Result: 

NG 

REPLACE ENGINE COOLANT TEMPERATURE SENSOR. Refer to  REMOVAL [09/2023 - ] 

Result: 

OK 

See step  11

HINT: 

Refer to REMOVAL [09/2023 - ]

Result

Result: 

NEXT 

See step  12

Pre-procedure1

• None

• Clear the DTCs.

  Powertrain > Engine > Clear DTCs 

  Result

  Proceed to
  NEXT

Post-procedure1

• Turn the ignition switch off and wait for at least 30 seconds.

Result: 

NEXT 

See step  13

Pre-procedure1

• Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

• Read the DTCs.

  Powertrain > Engine > Trouble Codes 

  Result

  Result	Proceed to
  DTCs are not output	A
  P3190-00 or P3191-00 is output	B

Post-procedure1

• None

Result: 

A 

END 

Result: 

B 

See step  14

HINT: 

Refer to REMOVAL [09/2023 - ]

Result

Result: 

NEXT 

See step  15

Pre-procedure1

• None

• Clear the DTCs.

  Powertrain > Engine > Clear DTCs 

  Result

  Proceed to
  NEXT

Post-procedure1

• Turn the ignition switch off and wait for at least 30 seconds.

Result: 

NEXT 

See step  16

Pre-procedure1

• Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

• Read the DTCs.

  Powertrain > Engine > Trouble Codes 

  Result

  Result	Proceed to
  DTCs are not output	A
  P3190-00 or P3191-00 is output	B

Post-procedure1

• None

Result: 

A 

END 

Result: 

B 

See step  17

HINT: 

Refer to REMOVAL [09/2023 - ]

Result

Result: 

NEXT 

See step  18

Pre-procedure1

• None

• Clear the DTCs.

  Powertrain > Engine > Clear DTCs 

  Result

  Proceed to
  NEXT

Post-procedure1

• Turn the ignition switch off and wait for at least 30 seconds.

Result: 

NEXT 

See step  19

Pre-procedure1

• Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

• Read the DTCs.

  Powertrain > Engine > Trouble Codes 

  Result

  Result	Proceed to
  DTCs are not output	A
  P3190-00 or P3191-00 is output	B

Post-procedure1

• None

Result: 

A 

END 

Result: 

B 

See step  20

HINT: 

Refer to REMOVAL [09/2023 - ]

Result

Result: 

NEXT 

See step  21

Pre-procedure1

• None

• Clear the DTCs.

  Powertrain > Engine > Clear DTCs 

  Result

  Proceed to
  NEXT

Post-procedure1

• Turn the ignition switch off and wait for at least 30 seconds.

Result: 

NEXT 

See step  22

Pre-procedure1

• Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

• Read the DTCs.

  Powertrain > Engine > Trouble Codes 

  Result

  Proceed to
  NEXT

Post-procedure1

• None

Result: 

NEXT 

END