LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> RX 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 132 (Can Communication System - Circuit Tests (2 Of 3)) >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Check Bus 2 Line [10/2022 - 08/2023] >> Procedure

Check Bus 2 Line [10/2022 - 08/2023]: Procedure

WARNING: This page is about a different car, the 2025 Lexus RX 350, 2024 Lexus RX 350, and 2023 Lexus RX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR OPEN IN CAN MAIN BUS LINES 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1127104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      C64-26 (CA4H) - C64-25 (CA4L) Cable disconnected from negative (-) battery terminal Below 70 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  29

    Result: 

    OK 

    See step  2

  2. CHECK FOR SHORT IN CAN BUS LINES 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1127104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))

      Standard Resistance

      Tester Connection Condition Specified Condition
      C64-26 (CA4H) - C64-25 (CA4L) Cable disconnected from negative (-) battery terminal 54 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  21

    Result: 

    OK 

    See step  3

  3. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1122669Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      C64-26 (CA4H) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C64-25 (CA4L) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  13

    Result: 

    OK 

    See step  4

  4. CHECK FOR SHORT TO GND IN CAN BUS LINE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY1122670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 DLC3 - -
      *a Component with harness connected
      (Central Gateway ECU (Network Gateway ECU))      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      C58-26 (CA4H) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C58-25 (CA4L) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    See step  5

  5. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C98 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-5 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  6

  6. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-6 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  10

    Result: 

    OK 

    See step  7

  7. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-8 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  11

    Result: 

    OK 

    See step  8

  8. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-7 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  12

  9. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C64 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-5 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  10. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Disconnect the A16 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-6 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 

  11. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Disconnect the C35 transmission floor shift assembly (shift control ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-8 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 

  12. CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Disconnect the C36 engine stop and start ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C58-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C98-7 (CANL) - C58-4 (CG)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ENGINE STOP AND START ECU. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 

  13. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C98 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-5 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  17

    Result: 

    OK 

    See step  14

  14. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-6 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  18

    Result: 

    OK 

    See step  15

  15. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-8 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  19

    Result: 

    OK 

    See step  16

  16. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-7 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  20

  17. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C64 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-5 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  18. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Disconnect the A16 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-6 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 

  19. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Disconnect the C35 transmission floor shift assembly (shift control ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-8 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 

  20. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Disconnect the C36 engine stop and start ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C58-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C98-7 (CANL) - C58-16 (BAT)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ENGINE STOP AND START ECU. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 

  21. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C98 No. 9 global CAN junction connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C98-5 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  25

    Result: 

    OK 

    See step  22

  22. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C98-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  26

    Result: 

    OK 

    See step  23

  23. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C98-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  27

    Result: 

    OK 

    See step  24

  24. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C98-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  28

  25. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Disconnect the C64 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C98-5 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

  26. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Disconnect the A16 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C98-6 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 

  27. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 
    1. Disconnect the C35 transmission floor shift assembly (shift control ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-4 (CANH) - C98-8 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT CONTROL ECU)) 

  28. CHECK FOR SHORT IN CAN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 
    1. Disconnect the C36 engine stop and start ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-3 (CANH) - C98-7 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ENGINE STOP AND START ECU. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU) 

  29. CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 
    1. Disconnect the C64 central gateway ECU (network gateway ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      EXCEPT TELEMATICS TRANSCEIVER (FOR TMC MADE)

      Tester Connection Condition Specified Condition
      C64-26 (CA4H) - C64-25 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU). Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    See step  30

  30. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 
    1. Reconnect the C64 central gateway ECU (network gateway ECU) connector.
    2. Disconnect the C98 No. 9 global CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-1 (CANH) - C98-5 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) 

    Result: 

    OK 

    See step  31

  31. CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 9 GLOBAL CAN JUNCTION CONNECTOR - ECM) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C98-2 (CANH) - C98-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 9 GLOBAL CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  32

  32. CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM) 
    1. Reconnect the C98 No. 9 global CAN junction connector.
    2. Disconnect the A16 ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A16-26 (CANH) - A16-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - NO. 9 GLOBAL CAN JUNCTION CONNECTOR) 

scientia non olet · About LEMON Manuals