LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> RX 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 127 (Hybrid Control System - Diagnostic Codes (5 Of 7)) >> HYBRID CONTROL SYSTEM (for THS-HEV Model) >> DTC P0C30-00: Hybrid/EV Battery State of Charge High [10/2022 - ] >> Procedure

DTC P0C30-00: Hybrid/EV Battery State of Charge High [10/2022 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus RX 350h, 2024 Lexus RX 350h, and 2023 Lexus RX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (HYBRID CONTROL) 

    Pre-procedure1

    • None.
    • Check for DTCs.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      P0C30-00 is output A
      P0C30-00 and other DTCs are output B

    Post-procedure1

    • Turn the ignition switch off.

    Result: 

    B 

    GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2022 - 10/2024]  , or Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2024 - ] 

    Result: 

    A 

    See step  2

  2. CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE) 

    HINT: 

    Refer to PROCEDURE - Step 2

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR POWER SOURCE) 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY) 

    HINT: 

    Refer to PROCEDURE - Step 3

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE HV BATTERY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    OK 

    See step  4

  4. CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE) 

    HINT: 

    Refer to PROCEDURE - Step 4

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  5

  5. BATTERY VOLTAGE SENSOR (GIB - GND) 

    HINT: 

    Refer to PROCEDURE - Step 5

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    OK 

    See step  6

  6. CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (HYBRID/EV BATTERY CURRENT) 

    Pre-procedure1

    • Turn the ignition switch to ON.
      NOTE:

      During the inspection, make sure to only turn the ignition switch to ON. Do not turn the ignition switch to ON (READY).

    • With the ignition switch ON, monitor Data List item "Hybrid/EV Battery Current" and "Hybrid/EV Battery Current for Hybrid/EV Battery Control" for 1 minute.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Hybrid/EV Battery Current
      Hybrid/EV Battery Current for Hybrid/EV Battery Control

      Result

      Result  Proceed to
      The value of Data List item "Hybrid/EV Battery Current" and "Hybrid/EV Battery Current for Hybrid/EV Battery Control" is -0.5 A or less or 0.5 A or more. A
      Other than above B

    Post-procedure1

    • Turn the ignition switch off.

    Result: 

    A 

    REPLACE BATTERY VOLTAGE SENSOR. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    B 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

  7. CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE) 

    HINT: 

    Refer to PROCEDURE - Step 9

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPLACE BATTERY VOLTAGE SENSOR. Refer to  REMOVAL [10/2022 - ] 

scientia non olet · About LEMON Manuals