Caution / Notice / Hint
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel filler opening lid sub-assembly removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED
| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Ultrasonic sensor*1 |
|
|
Refer to CALIBRATION [10/2022 - ] |
| Advanced Park | Refer to CALIBRATION [10/2022 - ] | ||
| Tires | for Gasoline Model AWD:
|
Dynamic Torque Control AWD System | Refer to CALIBRATION [10/2022 - ] |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below | |
| Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [10/2022 - ] | |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [10/2022 - ] | |
| Advanced Park | Refer to CALIBRATION [10/2022 - ] | ||
|
Initialize fold seat control ECU | Rear Power Seat Control System | Refer to INITIALIZATION [10/2022 - ] |
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
*2: Also necessary after performing a tire rotation.
*3: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
NOTE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
- To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted. Refer to PRECAUTION [10/2022 - ] Front Camera System except Gasoline Model: - Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
for Gasoline Model:- Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.
Refer to INITIALIZATION [10/2022 - ] Adaptive High Beam System LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) - Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link Power Back Door System Reset back door close position Refer to INITIALIZATION [10/2022 - ] Air Conditioning System except PHEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:- After the ignition switch is turned to ON, the servo motor and cooler expansion valve standard position is recognized.
-
COMPONENTS (REMOVAL)
| Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | See step 1 | - | - |
| 2 | TONNEAU COVER ASSEMBLY | 64910J | - | - | - |
| 3 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 4 | BATTERY SERVICE COVER PLATE | 58491E | - | - | - |
| 5 | DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL | - | - | - | - |
| 6 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 7 | REAR DECK FLOOR BOX LH | 64993D | - | - | - |
| *A | for Gasoline Model | *B | except Gasoline Model |
| *C | w/o Spare Tire | *D | w/ Spare Tire |
| Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 8 | REAR FLOOR BOARD REAR RH | 58417B | - | - | - |
| 9 | JUNCTION BLOCK SERVICE COVER | 58461H | - | - | - |
| 10 | REAR FLOOR BOARD REAR LH | 58418H | - | - | - |
| 11 | JUNCTION BLOCK SERVICE COVER LH | 58461J | - | - | - |
| 12 | DECK FLOOR BOX LH | 64997 | - | - | - |
| 13 | DECK FLOOR BOX RH | 64995 | - | - | - |
| 14 | SEPARATE REAR SEATBACK ASSEMBLY RH | - | - | - | - |
| 15 | SEPARATE REAR SEATBACK ASSEMBLY LH | - | - | - | - |
| 16 | DECK BOARD SET SUPPORT LH | 58393F | - | - | - |
| 17 | DECK BOARD SET SUPPORT | 58393E | - | - | - |
| 18 | REAR SEAT ASSEMBLY | - | - | - | - |
| *A | for Gasoline Model | *B | except Gasoline Model |
| *C | w/o Spare Tire | *D | w/ Spare Tire |
| Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 19 | REAR DOOR SCUFF PLATE LH | 67918A | - | - | - |
| 20 | NO. 3 BATTERY SERVICE COVER BOARD | 58467J | - | - | - |
| 21 | DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH | 62332C | - | - | - |
| 22 | REAR SEAT SIDE GARNISH LH | 62552F | - | - | - |
| 23 | REAR FLOOR FINISH PLATE | 58387B | - | - | - |
| 24 | ROPE HOOK ASSEMBLY | 66310H | See step 24 | - | - |
| 25 | NO. 1 LUGGAGE COMPARTMENT TRIM HOOK | 64725F | See step 25 | - | - |
| 26 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY | 81330 | - | - | - |
| 27 | DECK TRIM SIDE PANEL ASSEMBLY LH | 64740C | See step 27 | - | - |
| 28 | NO. 1 SPEAKER ASSEMBLY WITH BOX | 86150 | - | - | - |
| *A | w/ Woofer | - | - |
| Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 29 | REAR WHEEL LH | - | - | - | - |
| 30 | REAR BUMPER ASSEMBLY | - | - | - | - |
| 31 | ROCKER PANEL MOULDING RETAINER LH | 75866C | - | - | - |
| 32 | QUARTER WHEEL OPENING MOULDING LH | 75874A | See step 32 | - | - |
| 33 | REAR WHEEL HOUSE LINER LH | 65638 | - | - | - |
| Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 34 | FUEL FILLER OUTER OPENING LID | 77351A | See step 34 | - | - |
| 35 | FUEL TANK CAP ASSEMBLY | 77310A | - | - | - |
| 36 | FUEL FILLER OPENING LID SUB-ASSEMBLY | 77305A | See step 36 | - | - |
| *1 | FUEL INLET BOX RING | - | - |