Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery charger connector opening lid sub-assembly removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Replacement of service plug grip	High voltage fuse accumulated load history reset	DTCs are stored	Refer to UTILITY [08/2023 - ]

WARNING:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the appropriate service information .

Refer to PRECAUTION [08/2023 - ]

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NOTE:

When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
Refer to BEFORE DISCONNECTING BATTERY [10/2022 - ]
To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
Refer to INSPECTION MODE PROCEDURE [10/2022 - ]

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

LEARNING COMPLETES WHEN VEHICLE IS DRIVEN

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Stop and Start System	Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted.	Refer to PRECAUTION [10/2022 - ]
Lighting System (EXT)	for Gasoline Model: Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. except Gasoline Model: Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.	Refer to INITIALIZATION [10/2022 - ]
Front Camera System
Adaptive High Beam System

LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Power Back Door System	Reset back door close position	Refer to INITIALIZATION [10/2022 - ]
Air Conditioning System	for PHEV Model: After the ignition switch is turned to ON, the servo motor and cooler expansion valve standard position is recognized. except PHEV Model: After the ignition switch is turned to ON, the servo motor standard position is recognized.	-

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Power Back Door System

Reset back door close position

Refer to INITIALIZATION [10/2022 - ]

Air Conditioning System

for PHEV Model:

After the ignition switch is turned to ON, the servo motor and cooler expansion valve standard position is recognized.

except PHEV Model:

After the ignition switch is turned to ON, the servo motor standard position is recognized.

COMPONENTS (REMOVAL)

Fig 1: Charge Lid Opener Unit Removal Components (1 Of 6)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code
1	SERVICE PLUG GRIP	G3834	-	-	-

Fig 2: Charge Lid Opener Unit Removal Components (2 Of 6)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code
2	TONNEAU COVER ASSEMBLY	64910J	-	-	-
3	DECK BOARD ASSEMBLY	58410B	-	-	-
4	BATTERY SERVICE COVER PLATE	58491E	-	-	-
5	REAR DECK FLOOR BOX LH	64993D	-	-	-

Fig 3: Charge Lid Opener Unit Removal Components (3 Of 6)

Procedure		Part Name Code
6	REAR FLOOR BOARD REAR RH	58417B	-	-	-
7	JUNCTION BLOCK SERVICE COVER	58461H	-	-	-
8	REAR FLOOR BOARD REAR LH	58418H	-	-	-
9	JUNCTION BLOCK SERVICE COVER LH	58461J	-	-	-
10	DECK FLOOR BOX LH	64997	-	-	-
11	DECK FLOOR BOX RH	64995	-	-	-
12	SEPARATE REAR SEATBACK ASSEMBLY RH	-	-	-	-
13	SEPARATE REAR SEATBACK ASSEMBLY LH	-	-	-	-
14	DECK BOARD SET SUPPORT LH	58393F	-	-	-
15	DECK BOARD SET SUPPORT	58393E	-	-	-
16	REAR SEAT ASSEMBLY	-	-	-	-

Fig 4: Charge Lid Opener Unit Removal Components (4 Of 6)

Procedure		Part Name Code
17	REAR DOOR SCUFF PLATE RH	67917A	-	-	-
18	NO. 2 BATTERY SERVICE COVER BOARD	58466K	-	-	-
19	REAR DOOR OPENING TRIM WEATHERSTRIP RH	62331C	-	-	-
20	REAR SEAT SIDE GARNISH RH	62551F	-	-	-
21	REAR FLOOR FINISH PLATE	58387B	-	-	-
22	ROPE HOOK ASSEMBLY	66310H	See step 22	-	-
23	NO. 1 LUGGAGE COMPARTMENT TRIM HOOK	64725F	-	-	-
24	NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY	81330	-	-	-
25	DECK TRIM SIDE PANEL ASSEMBLY RH	64730B	See step 25	-	-

Fig 5: Charge Lid Opener Unit Removal Components (5 Of 6)

Procedure		Part Name Code
26	DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH	73360D	-	-	-
27	ROOF SIDE INNER GARNISH ASSEMBLY RH	62470A	-	-	-
28	REAR SEAT OUTER BELT ASSEMBLY RH	73360D	See step 28	-	-

Fig 6: Charge Lid Opener Unit Removal Components (6 Of 6)

Procedure		Part Name Code
29	AC CHARGER INLET CABLE	G9081C	See step 29	-	-
30	BATTERY CHARGE PORT LID SUB-ASSEMBLY	77304A	See step 30	-	-
31	FUEL FILLER OUTER OPENING LID	77351A	See step 31	-	-
32	CONNECTOR COVER	G9060B	-	-	-
33	BATTERY CHARGER CONNECTOR OPENING LID SUB-ASSEMBLY	58409E	See step 33	-	-