Installation [09/2014 - 11/2017]: Procedure

WARNING: This page is about a different car, the 2017 Lexus RC 350, 2017 Lexus RC 300, 2016 Lexus RC 350, 2016 Lexus RC 300, and 2015 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL V-BANK COVER BRACKET SUB-ASSEMBLY
1. Install the V-bank cover bracket sub-assembly to the cylinder head cover sub-assembly with the bolt.
  Torque: 10 N.m (102 kgf/cm, 7 ft.lbf)
INSTALL WIRE HARNESS CLAMP BRACKET
1. Install the wire harness clamp bracket to the camshaft housing sub-assembly RH with the bolt.
  Torque: 13 N.m (133 kgf/cm, 10 ft.lbf)
INSTALL ENGINE WIRE
1. Install the engine wire to the engine assembly.
INSTALL NO. 3 WATER BY-PASS PIPE
1. Connect the No. 9 water by-pass hose to the rear water by-pass joint and slide the clip to secure it.
2. Connect the No. 8 water by-pass hose to the water outlet pipe sub-assembly and slide the clip to secure it.
3. Install the No. 3 water by-pass pipe to the camshaft housing sub-assembly RH with the bolt.
  Torque: 10 N.m (102 kgf/cm, 7 ft.lbf)
INSTALL NO. 2 SURGE TANK STAY
1. Install the No. 2 surge tank stay to the camshaft housing sub-assembly LH with the bolt.
  Torque: 21 N.m (214 kgf/cm, 15 ft.lbf)
2. Connect the 2 clamps to the No. 2 surge tank stay.
INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY
1. Install the No. 2 fuel tube sub-assembly with the 2 bolts.
  Torque: 10 N.m (102 kgf/cm, 7 ft.lbf)
2. Connect the No. 2 fuel tube sub-assembly to the fuel delivery pipe sub-assembly and slide the clip to secure it.
  Refer to PRECAUTION [09/2014 - 11/2017]
INSTALL NO. 3 FUEL PIPE SUB-ASSEMBLY
Refer to PROCEDURE - Step 5
INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY
Refer to INSTALLATION [09/2014 - 11/2017]
INSTALL INJECTOR DRIVER
Refer to PROCEDURE - Step 1
INSTALL WATER PUMP PULLEY
Refer to PROCEDURE - Step 3

INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

for 2WD:

Temporarily install the V-ribbed belt tensioner assembly with the bolt (A) and (B).

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Tighten the 5 bolts to install the V-ribbed belt tensioner assembly.
Torque: 43 N.m (438 kgf/cm, 32 ft.lbf)

for AWD:

Temporarily install the V-ribbed belt tensioner assembly with the bolt (A) and (B).

Tighten the 4 bolts to install the V-ribbed belt tensioner assembly.
Torque: 43 N.m (438 kgf/cm, 32 ft.lbf)

INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
1. Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.
  Torque: 43 N.m (438 kgf/cm, 32 ft.lbf)
2. Connect the 2 clamps.
INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
1. Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.
  Torque: 43 N.m (438 kgf/cm, 32 ft.lbf)
INSTALL COMPRESSOR AND MAGNETIC CLUTCH (for 2WD)
Refer to PROCEDURE - Step 2 [09/2014 - 10/2015] , or refer to PROCEDURE - Step 3 [10/2015 - 11/2017]
TEMPORARILY TIGHTEN COMPRESSOR AND MAGNETIC CLUTCH (for AWD)
Refer to PROCEDURE - Step 2
INSTALL OIL FILTER BRACKET (for AWD)
Refer to PROCEDURE - Step 4
INSTALL COMPRESSOR AND MAGNETIC CLUTCH (for AWD)
Refer to PROCEDURE - Step 5
INSTALL GENERATOR ASSEMBLY
Refer to PROCEDURE - Step 1
INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
Refer to PROCEDURE - Step 2
INSTALL NO. 1 ENGINE COVER
Refer to PROCEDURE - Step 2
INSTALL NO. 2 ENGINE COVER
1. Install the No. 2 engine cover sub-assembly with the 3 clips.
2. Connect the clamp to the No. 2 engine cover sub-assembly.
INSTALL V-RIBBED BELT
Refer to PROCEDURE - Step 1
INSTALL IGNITION COIL ASSEMBLY
Refer to PROCEDURE - Step 2