Typical Enabling Conditions
WARNING: This page is about a different car, the 2017 Lexus RC 350, 2016 Lexus RC 350, and 2015 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) |
P0715, P0717 (Turbine speed sensor circuit) P2765, P2767 (Input speed sensor circuit) P0500, P0502, P0503 (Output speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P2810 (Shift solenoid valve SL4 circuit) P2819 (Shift solenoid valve SL5 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P2716 (Shift solenoid valve SLT circuit) P0115, P0117, P0118 (ECT sensor circuit) P0712, P0713 (ATF temperature sensor circuit (TFT sensor)) P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P0607, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system) U0100 (CAN communication system) |
| NSW switch | "D" and "not R" and "not N" |
| Duration time from shifting "N" to "D" | 4 sec. or more |
| ATF temperature | -10°C (14°F) or more |
| Engine | Starting |
ON MALFUNCTION (A)
| Turbine speed | 270 rpm or more |
| TCM selected gear | 1st |
| Turbine speed - Output speed (NT - NO) x 1st gear ratio | 150 rpm or more |
ON MALFUNCTION (B)
| Turbine speed | 270 rpm or more |
| TCM selected gear | 2nd |
| TCM indicated pressure value of SL5 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio | 150 rpm or more |
| Output speed | More than 0 rpm |
ON MALFUNCTION (C)
| Turbine speed | 270 rpm or more |
| TCM selected gear | 3rd |
| TCM indicated pressure value of SL3 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio | 150 rpm or more |
| Output speed | More than 0 rpm |
ON MALFUNCTION (D)
| Turbine speed | 270 rpm or more |
| TCM selected gear | 4th |
| TCM indicated pressure value of SL4 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 4th gear ratio | 150 rpm or more |
| Output speed | More than 0 rpm |
ON MALFUNCTION (E)
| TCM selected gear | 5th, 6th, 7th or 8th |
| TCM indicated pressure value of SL2 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
| Time after transmission shifts to TCM selected gear (when detected abnormal shift) |
1.5 sec. or more |
| Input speed | 0 rpm or less or 50 rpm or more |
ON MALFUNCTION (F)
| Output speed sensor circuit | Not circuit malfunction |
| TCM selected gear | 1st, 2nd, 3rd, 4th or 5th |
| TCM indicated pressure value of SL1 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
| Input speed when output speed sensor fail-safe function does not operate | 12799 rpm or less |
| Transmission range | "D" and "not R" and "not N" |
| When one of following conditions is met | Condition (1), (2) or (3) |
| - Condition (1): Oil pressure switch indication | ON |
| - Condition (2): Oil pressure switch | OFF malfunction |
| - Condition (3): Oil pressure switch | ON malfunction |