LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 450h+ Base >> Repair and Diagnosis >> Body & Frame >> Seats >> Seats - Service Information (1 Of 2) >> Rear Seat Assembly >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

  1. REMOVE TONNEAU COVER ASSEMBLY 

    Refer to PROCEDURE - Step 1 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 1 [03/2024 - ]

  2. REMOVE DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 2 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 2 [03/2024 - ]

  3. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side) 
    1. GTY1054800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side) 
    1. GTY1055433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side) 
    1. GTY1054793Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE REAR SEATBACK ASSEMBLY RH 
    1. GTY1053470Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener - -
      Direction to defeat Remove in this Direction
      1. Fold the rear seatback assembly RH forward.
      2. Disengage the 3 clips.
      3. Disengage the 2 fasteners.
      4. Remove the 2 bolts.
      5. Disengage the 2 guides and shift the rear seatback assembly RH.
        NOTE:

        Be careful not to damage the vehicle body.

    2. GTY1054731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Band - -
      1. Remove the nut and disconnect the floor anchor of the rear center seat outer belt assembly.
      2. Remove the floor anchor part of the rear center seat outer belt assembly from the band of the rear seatback assembly RH.
        NOTE:

        Be careful not to damage the vehicle body.

      3. Disengage the 2 clamps and disconnect the connecter. (w/ Seat Heater System)
      4. Remove the rear seatback assembly RH.
        NOTE:

        Be careful not to damage the vehicle body.

  7. REMOVE REAR SEATBACK ASSEMBLY LH 
    1. GTY1055314Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener - -
      Direction to defeat Remove in this Direction
      1. Fold the rear seatback assembly LH forward.
      2. Disengage the 2 clips.
      3. Disengage the 2 fasteners.
      4. Remove the 2 bolts.
      5. Disengage the 2 guides and shift the rear seatback assembly LH.
        NOTE:

        Be careful not to damage the vehicle body.

      6. Disengage the 2 clamps and disconnect the connecter. (w/ Seat Heater System)
      7. Remove the rear seatback assembly LH.
  8. REMOVE REAR SEAT CUSHION ASSEMBLY 
    1. GTY1052553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rear Seat Cushion Frame Hook (Front Side) *b Rear Seat Cushion Frame Hook (Rear Side)
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
      1. Lift the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the rear seat cushion lock hooks.

        Standard Measurement

        Area Measurement Area Measurement
        A 30 mm (1.18 in.) B 60 mm (2.36 in.)
        C 80 mm (3.15 in.) D 150 mm (5.91 in.)
        NOTE:
        • Disengage each hook at the front part of the rear seat cushion frame one area at a time.
        • Be sure to hold the parts of the seat cushion assembly directly next to the rear seat cushion frame hooks when lifting it. Lifting a different part of the cushion may deform the rear seat cushion frame.
      2. Disengage the 2 rear seat cushion frame hooks on the rear side of the rear seat cushion assembly as shown in the illustration.
      3. Disconnect the 2 connecters. (w/ Seat Heater System)
      4. Remove the rear seatback assembly RH.
        NOTE:

        Be careful not to damage the vehicle body.

  9. REMOVE REAR SEAT CUSHION LOCK HOOK 
    1. GTY1053282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for RH Side *B for LH Side
scientia non olet · About LEMON Manuals