LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 61 (Engine Control System - Service Information) >> Relay >> On-Vehicle Inspection [11/2021 - ] >> Procedure

On-Vehicle Inspection [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT VVT RELAY (VVT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the VVT relay (VVT).

  2. INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 1) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the No. 1 electronic fuel injection main relay (EFI-MAIN NO. 1).

  3. INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 2) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the No. 2 electronic fuel injection main relay (EFI-MAIN NO. 2).

  4. INSPECT NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 3) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the No. 3 electronic fuel injection main relay (EFI-MAIN NO. 3).

  5. INSPECT INJECTOR RELAY (D INJ) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the injector relay (D INJ).

  6. INSPECT IGP RELAY (IGP NO. 1) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the IGP relay (IGP NO. 1).

scientia non olet · About LEMON Manuals