LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 33 (Hybrid Control System - Diagnostic Codes (5 Of 5) & Circuit Tests) >> Hybrid Control System >> Shift Paddle Switch Circuit [11/2021 - ] >> Procedure

Shift Paddle Switch Circuit [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL) 
    1. Read the Data List using the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Sports Shift UP Signal
      Sports Shift DOWN Signal

      Powertrain > Hybrid Control > Data List 

      Tester Display Measurement Item Range Normal Condition
      Sports Shift UP Signal Sports shift UP signal ON or OFF ON:
      Shift paddle switch RH (+) operated
      OFF:
      Shift paddle switch RH (+) not operated
      Sports Shift DOWN Signal Sport shift DOWN signal ON or OFF ON:
      Shift paddle switch LH (-) operated
      OFF:
      Shift paddle switch LH (-) not operated

      Result

      Result Proceed to
      The GTS display changes according to the shift paddle switch (transmission shift switch assembly) operation. A
      The GTS display does not change according to the shift paddle switch (transmission shift switch assembly) operation. B
    2. Turn the ignition switch off.

    Result: 

    A 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2021 - ] 

    Result: 

    B 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU) 
    1. Disconnect the hybrid vehicle control ECU connector.
    2. Measure the resistance according to the value(s) in the table below when the shift paddle switch (transmission shift switch assembly) is moved to each position.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D67-17 (SFTU) - Body ground Shift paddle switch RH (+) operated Below 2.5 Ω
      D67-5 (SFTD) - Body ground Shift paddle switch LH (-) operated Below 2.5 Ω
      D67-17 (SFTU) - Body ground Shift paddle switch RH (+) not operated 1 MΩ or higher
      D67-5 (SFTD) - Body ground Shift paddle switch LH (-) not operated 1 MΩ or higher
      GTY1059094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rear view of wire harness connector
      (to Hybrid Vehicle Control ECU)
    3. Reconnect the hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND) 
    1. Disconnect the spiral cable sub-assembly connector.
    2. Disconnect the hybrid vehicle control ECU connector.
    3. Measure the resistance according to the value(s) in the table below. (for Manual Tilt and Manual Telescopic Steering Column)

      Standard Resistance (Check for Open)

      10 kΩ or higher

      Tester Connection Condition Specified Condition
      D25-8 (SUP) - D67-17 (SFTU) Always Below 1 Ω
      D25-1 (SDN) - D67-5 (SFTD) Always Below 1 Ω
      D25-2 (ECC) - Body ground Always Below 1 Ω

      Standard Resistance (Check for Short)

      Tester Connection Condition Specified Condition
      D25-8 (SUP) or D67-17 (SFTU) - Body ground Always 10 kΩ or higher
      D25-1 (SDN) or D67-5 (SFTD) - Body ground Always 10 kΩ or higher
    4. Measure the resistance according to the value(s) in the table below. (for Power Tilt and Power Telescopic Steering Column)

      Standard Resistance (Check for Open)

      Tester Connection Condition Specified Condition
      D144-8 (SUP) - D67-17 (SFTU) Always Below 1 Ω
      D144-1 (SDN) - D67-5 (SFTD) Always Below 1 Ω
      D144-2 (ECC) - Body ground Always Below 1 Ω

      Standard Resistance (Check for Short)

      Tester Connection Condition Specified Condition
      D144-8 (SUP) or D67-17 (SFTU) - Body ground Always 10 kΩ or higher
      D144-1 (SDN) or D67-5 (SFTD) - Body ground Always 10 kΩ or higher
    5. Reconnect the hybrid vehicle control ECU connector.
    6. Reconnect the spiral cable sub-assembly connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT SPIRAL CABLE SUB-ASSEMBLY 

    Refer to INSPECTION [11/2021 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    OK 

    See step  5

  5. INSPECT SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) LH 

    Refer to INSPECTION [11/2021 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) LH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) RH 

    Refer to INSPECTION [11/2021 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) RH. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    OK 

    See step  7

  7. INSPECT NO. 1 SWITCH WIRE 
    1. Disconnect the No. 1 switch wire connector.
    2. Measure the resistance according to the value(s) in the table below when the shift paddle switch (transmission shift switch assembly) is moved to each position.
      GTY1058577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (No. 1 Switch Wire)

      Standard Resistance

      Tester Connection Condition Specified Condition
      z30-4 (SDN) - z30-3 (ECC) Shift paddle switch LH (-) operated Below 2.5 Ω
      z30-2 (SUP) - z30-3 (ECC) Shift paddle switch RH (+) operated Below 2.5 Ω
      z30-4 (SDN) - z30-3 (ECC) Shift paddle switch LH (-) not operated 1 MΩ or higher
      z30-2 (SUP) - z30-3 (ECC) Shift paddle switch RH (+) not operated 1 MΩ or higher
    3. Reconnect the No. 1 switch wire connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2021 - ] 

    Result: 

    NG 

    REPLACE NO. 1 SWITCH WIRE. Refer to  REMOVAL [11/2021 - ] 

scientia non olet · About LEMON Manuals