LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 148 (Automatic Transaxle System - Diagnostic Codes (3 Of 3) & Circuit Tests) >> Automatic Transaxle System >> DTC P2756-7F: Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off [11/2021 - ] >> Procedure

DTC P2756-7F: Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P2756-7F) 
    1. Read the DTCs using the GTS.

      Powertrain > Transmission > Trouble Codes 

      Result

      Result Proceed to
      Only DTC P2756-7F is output A
      DTC P2756-7F and other DTCs are output B

      HINT: 

      • If any DTCs other than P2756-7F are output, perform troubleshooting for those DTCs first.
      • If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.

    Result: 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2021 - 03/2024]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [03/2024 - ] 

    Result: 

    See step  2

  2. INSPECT SOLENOID (SLU) VALVE 
    1. Remove the solenoid (SLU) valve.
      GTY745206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Solenoid (SLU) Valve)

      Refer to DISASSEMBLY [11/2021 - ]

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Solenoid (SLU) valve connector terminal 1 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK

      Valve moves and makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SOLENOID (SLU) VALVE. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    OK 

    See step  3

  3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY 
    1. Inspect the transmission valve body assembly.

      Refer to REMOVAL [11/2021 - ]

      OK

      There is no foreign matter on each valve and they operate smoothly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    OK 

    See step  4

  4. INSPECT TORQUE CONVERTER ASSEMBLY 
    1. Inspect the torque converter assembly.

      Refer to INSPECTION [11/2021 - ]

      OK

      The torque converter assembly is normal.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  REMOVAL [11/2021 - 03/2022]  , or refer to  REMOVAL [03/2022 - 03/2024]  , or refer to  REMOVAL [03/2024 - ] 

    Result: 

    OK 

    See step  5

  5. REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY 

    Refer to REMOVAL [11/2021 - 03/2022] , or refer to REMOVAL [03/2022 - 03/2024] , or refer to REMOVAL [03/2024 - ]

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    PERFORM REGISTRATION. Refer to  REGISTRATION [11/2021 - ]