Rear Television Camera Communication Stop Mode [11/2021 - ]: Procedure
- CHECK VEHICLE TYPE
- Check vehicle type.
Result
Result Proceed to w/o Parking Support Brake System A w/ Parking Support Brake System B
Result:
B
See step 5
Result:
A
See step 2
- Check vehicle type.
- CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
- Disconnect the cable from the negative (-) auxiliary battery terminal.
- Disconnect the P28 rear television camera assembly connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition P28-1 (CANH) - P28-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Result
Result OK NG
Result:
NG
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)
Result:
OK
See step 3
- CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition P28-3 (CGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω - Reconnect the cable to the negative (-) auxiliary battery terminal.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition P28-4 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V Result
Result OK NG
Result:
OK
REPLACE REAR TELEVISION CAMERA ASSEMBLY. Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]
Result:
NG
See step 4
- Measure the resistance according to the value(s) in the table below.
- CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
Refer to Image from Camera for Parking Assist Monitor is Abnormal [11/2021 - ]
Result
Result OK NG Result:
OK
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to REMOVAL [11/2021 - ]
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
- CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
- Disconnect the cable from the negative (-) auxiliary battery terminal.
- Disconnect the P29 rear television camera assembly connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition P29-1 (CANH) - P29-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Result
Result OK NG
Result:
NG
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)
Result:
OK
See step 6
- CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition P29-3 (CGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω - Reconnect the cable to the negative (-) auxiliary battery terminal.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition P29-4 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V Result
Result OK NG
Result:
OK
REPLACE REAR TELEVISION CAMERA ASSEMBLY. Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]
Result:
NG
See step 7
- Measure the resistance according to the value(s) in the table below.
- CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
Refer to Image from Camera for Parking Assist Monitor is Abnormal [11/2021 - ]
Result
Result OK NG Result:
OK
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to REMOVAL [11/2021 - ]
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)