LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 102 (Can Communication System - Circuit Tests (2 Of 9)) >> CAN COMMUNICATION SYSTEM (for HEV Model) >> Main Body ECU Communication Stop Mode [11/2021 - ] >> Procedure

Main Body ECU Communication Stop Mode [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) MAIN LINE) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the D50 main body ECU (multiplex network body ECU) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D50-2 (CANH) - D50-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Result 
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) 

    Result: 

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT) 
    1. Remove the main body ECU (multiplex network body ECU).

      Refer to REMOVAL [11/2021 - ]

    2. Reconnect the cable to the negative (-) auxiliary battery terminal.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      MB-26 (BECU) - Body ground Ignition switch off 11 to 14 V
      GTY1060297Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Power Distribution Box Assembly
      NOTE:

      Perform this inspection with the wire harness connected to the power distribution box assembly.

      Result

      Result 
      OK
      NG

    Result: 

    OK 

    CHECK ECU POWER SOURCE CIRCUIT. Refer to  IG Signal Circuit [11/2021 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the 9K power distribution box assembly connector.
    3. Reconnect the cable to the negative (-) auxiliary battery terminal.
    4. Measure the voltage according to the value(s) in the table below.
      GTY1065065Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Power Distribution Box Assembly)

      Standard Voltage

      Tester Connection Condition Specified Condition
      9K-1 - Body ground Ignition switch off 11 to 14 V

      Result

      Result 
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT) 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the 9C power distribution box assembly connector.
    3. Measure the resistance according to the value(s) in the table below.
      GTY1063246Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Power Distribution Box Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      9C-11 - 9C-34 Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

      Result

      Result 
      OK
      NG

    Result: 

    OK 

    REPLACE POWER DISTRIBUTION BOX ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT) 

scientia non olet · About LEMON Manuals