Caution / Notice / Hint
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel lid lock with motor assembly removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR HEV MODEL)
| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
|
Initialize fold seat control ECU | Rear Power Seat Control System | Refer to INITIALIZATION [11/2021 - ] |
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
NOTE:
- To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
- After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link Lighting System (EXT) Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. Refer to INITIALIZATION [11/2021 - ] Front Camera System Adaptive High Beam System - Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link E-latch System - Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. Refer to INITIALIZATION [11/2021 - ] Power Back Door System Reset back door close position Refer to INITIALIZATION [11/2021 - ] Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR GASOLINE MODEL)
| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
|
Initialize fold seat control ECU | Rear Power Seat Control System | Refer to INITIALIZATION [11/2021 - ] |
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
NOTE:
- To prevent the key from being locked in the vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
- After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link Lighting System (EXT) Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. Refer to INITIALIZATION [11/2021 - ] Front Camera System Adaptive High Beam System Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Refer to PRECAUTION [11/2021 - 03/2023] , or refer to PRECAUTION [03/2023 - 03/2024] , or refer to PRECAUTION [03/2024 - ] - Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link E-latch System - Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. Refer to INITIALIZATION [11/2021 - ] Power Back Door System Reset back door close position Refer to INITIALIZATION [11/2021 - ] Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -
COMPONENTS (REMOVAL)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | REAR SEAT ASSEMBLY | - | - | - | - |
| 2 | BATTERY SERVICE COVER PLATE | 58491E | - | - | - |
| 3 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 4 | REAR FLOOR BOARD REAR RH | 58417B | - | - | - |
| 5 | JUNCTION BLOCK SERVICE COVER | 58461H | - | - | - |
| 6 | REAR FLOOR BOARD REAR LH | 58418H | - | - | - |
| 7 | DECK FLOOR BOX RH | 64995 | - | - | - |
| 8 | DECK FLOOR BOX LH | 64997 | - | - | - |
| *A | w/o Spare Tire | *B | w/ Spare Tire |
| *C | for Gasoline Model | *D | for HEV Model |
| *E | for Manual Seat | - | - |
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 9 | REAR DOOR SCUFF PLATE LH | 67918A | - | - | - |
| 10 | NO. 3 BATTERY SERVICE COVER BOARD | 58467J | - | - | - |
| 11 | REAR FLOOR FINISH PLATE | 58387B | - | - | - |
| 12 | REAR DOOR OPENING TRIM WEATHERSTRIP LH | 62332A | - | - | - |
| 13 | NO. 1 SIDE TRIM BASE COVER LH | 62525D | - | - | - |
| 14 | REAR SEAT SIDE GARNISH LH | 62552F | - | - | - |
| 15 | ROPE HOOK ASSEMBLY | 66310H | See step 15 | - | - |
| 16 | LUGGAGE HOLD BELT STRIKER ASSEMBLY | 58460D | - | - | - |
| 17 | NO. 1 LUGGAGE COMPARTMENT TRIM HOOK | 64725F | See step 17 | - | - |
| 18 | DECK TRIM SIDE PANEL ASSEMBLY | - | See step 18 | - | - |
| 19 | FUEL LID LOCK WITH MOTOR ASSEMBLY | 77030A | See step 19 | - | - |
| *A | for HEV Model | *B | for Gasoline Model |