Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear bumper assembly removal/installation are shown below.

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Lighting system (EXT) Cornering lights	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.	Refer to INITIALIZATION [12/2023 - ]
Front camera system		Refer to INITIALIZATION [12/2023 - ]

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power back door system	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	Refer to INITIALIZATION [12/2023 - ]
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized.	-

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.
If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.
- Target Adjustment (Triangle Target):
  Refer to TARGET ADJUSTMENT (TRIANGLE TARGET) [12/2023 - ]
- Driving Adjustment:
  Refer to DRIVING ADJUSTMENT [12/2023 - ]
When the rear bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform ultrasonic sensor detection angle measurement.
Refer to CALIBRATION [12/2023 - ]

COMPONENTS (REMOVAL)

Fig 1: Rear Bumper Removal Components

Procedure		Part Name Code
1	PRECAUTION	-	See step 1	-	-
2	DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL	-	-	-	-
3	REAR BUMPER STEP	52351	See step 3	-	-
4	REAR BUMPER BAR PLATE	52179B	See step 4	-	-
5	REAR COMBINATION LIGHT COVER LH	81498	See step 5	-	-
6	REAR COMBINATION LIGHT COVER RH	81497	See step 5	-	-
7	REAR BUMPER CORNER EXTENSION LH	52166B	-	-	-
8	REAR BUMPER CORNER EXTENSION RH	52165D	-	-	-
9	REAR BUMPER FILLER LH	52553	See step 9	-	-
10	REAR BUMPER FILLER RH	52552	See step 9	-	-
11	REAR QUARTER PANEL MUDGUARD LH	76626D	See step 11	-	-
12	REAR QUARTER PANEL MUDGUARD RH	76625D	See step 11	-	-
13	REAR BUMPER SIDE SEAL LH	52592	See step 13	-	-
14	REAR BUMPER SIDE SEAL RH	52591	See step 13	-	-
15	QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH	75606A	See step 15	-	-
16	QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH	75605A	See step 15	-	-
17	REAR BUMPER ASSEMBLY	-	See step 17	-	-

*A	w/ Hands Free Power Back Door	*B	w/ Mudguard
*C	w/o Mudguard	-	-