LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> ES 350 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 47 (Engine Mechanical System (A25A-FXS) - Service Information (1 Of 3)) >> Cylinder Head Gasket >> Removal [06/2018 - 08/2020] >> Procedure

Removal [06/2018 - 08/2020]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND 

    Refer to REMOVAL [06/2018 - 08/2020] 

  2. REMOVE ENGINE HANGERS 

    See step  54

  3. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY 

    Refer to PROCEDURE - Step 2

  4. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  5. REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY) 

    Refer to PROCEDURE - Step 4

  6. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR 

    Refer to PROCEDURE - Step 5

  7. REMOVE MANIFOLD STAY 

    Refer to PROCEDURE - Step 17

  8. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 7

  9. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY 

    Refer to PROCEDURE - Step 6

  10. REMOVE THROTTLE BODY GASKET 

    Refer to PROCEDURE - Step 7

  11. REMOVE EGR COOLER ASSEMBLY 

    Refer to PROCEDURE - Step 10

  12. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 5

  13. REMOVE NO. 4 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 12

  14. REMOVE EGR VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 13

  15. REMOVE NO. 3 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 14

  16. REMOVE NO. 2 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 15

  17. REMOVE INTAKE MANIFOLD 

    Refer to PROCEDURE - Step 9

  18. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET 

    Refer to PROCEDURE - Step 10

  19. DISCONNECT FUEL TUBE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 5

  20. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  21. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure) 

    Refer to PROCEDURE - Step 8

  22. REMOVE NO. 7 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 21

  23. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  24. REMOVE NO. 1 DELIVERY PIPE SPACER 

    Refer to PROCEDURE - Step 11

  25. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 12

  26. REMOVE NO. 5 ENGINE WIRE 

    Refer to PROCEDURE - Step 13

  27. REMOVE PORT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 14

  28. REMOVE FUEL DELIVERY PIPE 

    Refer to PROCEDURE - Step 8

  29. REMOVE DIRECT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 9

  30. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  31. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 

    Refer to PROCEDURE - Step 33

  32. REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 2

  33. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side) 

    Refer to PROCEDURE - Step 2

  34. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side) 

    Refer to PROCEDURE - Step 3

  35. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY 

    Refer to PROCEDURE - Step 2

  36. REMOVE O-RING 

    Refer to PROCEDURE - Step 3

  37. REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY 

    Refer to PROCEDURE - Step 4

  38. REMOVE CAM TIMING CONTROL MOTOR O-RING 

    Refer to PROCEDURE - Step 5

  39. REMOVE CRANKSHAFT PULLEY ASSEMBLY 

    Refer to PROCEDURE - Step 19 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 21 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 19 [10/2019 - ]

  40. REMOVE WATER OUTLET 

    Refer to PROCEDURE - Step 20 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 22 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 20 [10/2019 - ]

  41. REMOVE WATER BY-PASS OUTLET SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 21 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 23 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 21 [10/2019 - ]

  42. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 22 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 24 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 22 [10/2019 - ]

  43. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 23 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 25 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 23 [10/2019 - ]

  44. REMOVE ENGINE MOUNTING BRACKET RH 

    Refer to PROCEDURE - Step 24 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 26 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 24 [10/2019 - ]

  45. REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 26 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 28 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 26 [10/2019 - ]

  46. REMOVE TIMING CHAIN COVER OIL SEAL 

    Refer to PROCEDURE - Step 27 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 29 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 27 [10/2019 - ]

  47. SET NO. 1 CYLINDER TO TDC (COMPRESSION) 

    Refer to PROCEDURE - Step 28 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 30 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 28 [10/2019 - ]

  48. REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 29 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 31 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 29 [10/2019 - ]

  49. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 30 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 32 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 30 [10/2019 - ]

  50. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 31 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 33 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 31 [10/2019 - ]

  51. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 32 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 34 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 32 [10/2019 - ]

  52. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 33 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 35 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 33 [10/2019 - ]

  53. REMOVE NO. 1 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 34 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 36 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 34 [10/2019 - ]

  54. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 35 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 37 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 35 [10/2019 - ]

  55. REMOVE TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 36 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 38 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 36 [10/2019 - ]

  56. REMOVE FUEL PUMP LIFTER GUIDE 

    Refer to PROCEDURE - Step 39 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 41 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 39 [10/2019 - ]

  57. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 40 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 42 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 40 [10/2019 - ]

  58. REMOVE CAMSHAFT BEARING CAP 

    Refer to PROCEDURE - Step 41 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 43 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 41 [10/2019 - ]

  59. REMOVE CAMSHAFT 

    Refer to PROCEDURE - Step 42 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 44 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 42 [10/2019 - ]

  60. REMOVE NO. 2 CAMSHAFT 

    Refer to PROCEDURE - Step 43 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 45 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 43 [10/2019 - ]

  61. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 44 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 46 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 44 [10/2019 - ]

  62. REMOVE VALVE LASH ADJUSTER ASSEMBLY 

    Refer to PROCEDURE - Step 45 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 47 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 45 [10/2019 - ]

  63. REMOVE VALVE STEM CAP 

    Refer to PROCEDURE - Step 46 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 48 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 46 [10/2019 - ]

  64. REMOVE CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 48 [06/2018 - 07/2019] , or refer to PROCEDURE - Step 50 [07/2019 - 10/2019] , or refer to PROCEDURE - Step 49 [10/2019 - ]

  65. REMOVE CYLINDER HEAD GASKET 
    GTY759932Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the cylinder head gasket from the cylinder block sub-assembly.
  66. INSPECT CYLINDER HEAD SET BOLT 

    Refer to PROCEDURE - Step 18

  67. INSPECT CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 1

scientia non olet · About LEMON Manuals