LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> ES 350 Base >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Electronically Controlled Brake System (Except Hybrid) - Diagnostic Codes (2 Of 4) >> ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) >> DTC C0512-12: Right Rear Wheel Speed Sensor Circuit Short to Battery [08/2020 - ] >> Procedure

DTC C0512-12: Right Rear Wheel Speed Sensor Circuit Short to Battery [08/2020 - ]: Procedure

  1. CHECK VEHICLE 
    1. Check the vehicle specification.

      Result

      Result Proceed to
      for 2WD (w/o AVS) A
      for 2WD (w/ AVS) B
      for AWD C

    Result: 

    B 

    See step  6

    Result: 

    C 

    See step  10

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY806194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
      (to Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH))

      OK

      The connector is securely connected.

    2. Disconnect the b2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.
    3. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    4. Turn the engine switch on (IG).
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      b2-2 (RA+) - b2-1 (RA-) Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH. Refer to  REMOVAL [06/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY784760Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))

      OK

      The connector is securely connected.

    2. Disconnect the bN1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    3. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    4. Turn the engine switch on (IG).
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      bN1-1 (RR+) - bN1-2 (RR-) Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY 

    Result: 

    NG 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY784761Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))

      OK

      The connector is securely connected.

    2. Disconnect the A40 skid control ECU (brake actuator assembly) connector.
    3. Disconnect the bN1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    4. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      bN1-2 (RR-) - Body ground Always Below 1.5 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

      OK

      The connector is securely connected.

    2. Disconnect the A40 skid control ECU (brake actuator assembly) connector.
    3. Disconnect the bN1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    4. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      bN1-1 (RR+) or A40-22 (RR+) - bN1-2 (RR-) or A40-37 (RR-) Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY806194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
      (to Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH))

      OK

      The connector is securely connected.

    2. Disconnect the b2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.
    3. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    4. Turn the engine switch on (IG).
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      b2-2 (RA+) - b2-1 (RA-) Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH. Refer to  REMOVAL [06/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY778879Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))

      OK

      The connector is securely connected.

    2. Disconnect the bN5 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    3. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    4. Turn the engine switch on (IG).
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      bN5-1 (RR+) - bN5-2 (RR-) Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY 

    Result: 

    NG 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

      OK

      The connector is securely connected.

      GTY778880Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))
    2. Disconnect the A40 skid control ECU (brake actuator assembly) connector.
    3. Disconnect the bN5 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    4. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      bN5-2 (RR-) - Body ground Always Below 1.5 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

      OK

      The connector is securely connected.

    2. Disconnect the A40 skid control ECU (brake actuator assembly) connector.
    3. Disconnect the bN5 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
    4. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      bN5-1 (RR+) or A40-22 (RR+) - bN5-2 (RR-) or A40-37 (RR-) Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  10. CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT) 
    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.
      GTY806194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
      (to Rear Speed Sensor RH)

      OK

      The connector is securely connected.

    2. Disconnect the b2 rear speed sensor RH connector.
    3. Check both the connector case and the terminals for deformation and corrosion.

      OK

      No deformation or corrosion.

    4. Turn the engine switch on (IG).
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      b2-2 (RA+) - b2-1 (RA-) Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SPEED SENSOR RH. Refer to  REMOVAL [08/2020 - ] 

    Result: 

    NG 

    See step  3

scientia non olet · About LEMON Manuals