LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> RX 500h >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System (14 Inch Display) - Diagnostic Codes (2 Of 2) & Symptom Tests >> AUDIO AND VISUAL SYSTEM (for 14 Inch Display) >> DTC C1622-87: Rear Camera Image Signal Missing Message [10/2022 - ] >> Procedure

DTC C1622-87: Rear Camera Image Signal Missing Message [10/2022 - ]: Procedure

  1. CHECK PARKING ASSIST MONITOR SYSTEM 
    1. Check if the parking assist monitor system is malfunctioning.

      HINT: 

      Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - ]

      Result

      Result Proceed to
      Malfunction does not occur A
      Malfunction occurs B

    Result: 

    GO TO PARKING ASSIST MONITOR SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - ] 

    Result: 

    See step  2

  2. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      w/o Parking Support Brake System A
      w/ Parking Support Brake System B

    Result: 

    See step  4

    Result: 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) 

    Pre-procedure1

    • Disconnect the C146 radio and display receiver assembly connector.
    • Disconnect the M28 rear television camera assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      C146-3 (CVO+) - M28-6 (CV+) Always Below 1 Ω Ω
      C146-4 (CVO-) - M28-5 (CV-) Always Below 1 Ω Ω
      C146-1 (GGND) - M28-3 (CGND) Always Below 1 Ω Ω
      C146-3 (CVO+) or M28-6 (CV+) - Body ground Always 10 kΩ or higher
      C146-4 (CVO-) or M28-5 (CV-) - Body ground Always 10 kΩ or higher
      C146-1 (GGND) or M28-3 (CGND) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) 

    Pre-procedure1

    • Disconnect the C146 radio and display receiver assembly connector.
    • Disconnect the M29 rear television camera assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      C146-3 (CVO+) - M29-6 (CV+) Always Below 1 Ω Ω
      C146-4 (CVO-) - M29-5 (CV-) Always Below 1 Ω Ω
      C146-1 (GGND) - M29-3 (CGND) Always Below 1 Ω Ω
      C146-3 (CVO+) or M29-6 (CV+) - Body ground Always 10 kΩ or higher
      C146-4 (CVO-) or M29-5 (CV-) - Body ground Always 10 kΩ or higher
      C146-1 (GGND) or M29-3 (CGND) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR