Installation [10/2022 - ]: Procedure

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   1. Install a new gasket to the engine coolant temperature sensor.
   2. Using SST, install the engine coolant temperature sensor to the cylinder head sub-assembly.
      • SST: 09817-33191 

      Torque: 19.6 N*m (200 kgf*cm, 14 ft.*lbf) 

      NOTE:

      If the engine coolant temperature sensor has been struck or dropped, replace it.

   3. Connect the engine coolant temperature sensor connector.

HINT: 

Perform this procedure only when replacement of the engine coolant temperature sensor (for Cylinder Head Side) is necessary.

Refer to INSTALLATION [10/2022 - ]

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Torque Wrench Fulcrum Length

   *b

   Ball Joint Lock Nut Wrench

   1. Install a new gasket to the engine coolant temperature sensor.
   2. Using a ball joint lock nut wrench, install the engine coolant temperature sensor to the water inlet housing.

      Specified tightening torque 

      Torque: 19.6 N*m (200 kgf*cm, 14 ft.*lbf) 

      NOTE:

      If the engine coolant temperature sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [10/2022 - ]

      • When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        10.2 N*m (104 kgf*cm, 8 ft.*lbf)

   3. Connect the engine coolant temperature sensor connector.

HINT: 

Perform this procedure only when replacement of the engine coolant temperature sensor (for Water Inlet Housing Side) is necessary.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

HINT: 

Perform this procedure only when replacement of the engine coolant temperature sensor (for Water Inlet Housing Side) is necessary.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

HINT: 

Perform this procedure only when replacement of the engine coolant temperature sensor (for Water Inlet Housing Side) is necessary.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

HINT: 

Perform this procedure only when replacement of the engine coolant temperature sensor (for Water Inlet Housing Side) is necessary.

Refer to INSTALLATION [10/2022 - ]

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   1. Apply a light coat of engine coolant to the O-ring of the engine coolant temperature sensor.
   2. Install the engine coolant temperature sensor to the front water by-pass joint with a new clip.
      NOTE:

      • If the engine coolant temperature sensor has been struck or dropped, replace it.
      • If reusing the engine coolant temperature sensor, be sure to inspect the O-ring.
      • Make sure that the O-ring is not cracked or moved out of place when installing the engine coolant temperature sensor.
   3. Connect the engine coolant temperature sensor connector.

Refer to REPLACEMENT [10/2022 - ]

1. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

   Refer to INITIALIZATION [10/2022 - ]

Refer to WORK PROCEDURE [10/2022 - ]

HINT: 

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Refer to AUTOMATIC LEARNING CHART [10/2022 - 08/2023] , or refer to AUTOMATIC LEARNING CHART [08/2023 - ]