Installation [03/2023 - 03/2024]: Procedure

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   1. Install the 10 hole plugs to the rear suspension member sub-assembly.

      HINT: 

      There are 2 different shapes of hole plug.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath	-	-
   	Front of the Vehicle		Outside of the Vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
      NOTE:

      • Position the rear suspension member front body mounting cushion in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Hold	-	-
   	Turn	-	-

   1. Install SST as shown in the illustration.
      • SST: 09570-24011 
      • SST: 09830-10010 
        1. 09830-01010
        2. 09830-01020
        3. 09830-01040
        4. 09830-01050
      NOTE:

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

   2. Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.
      • SST: 09570-24011 
      • SST: 09830-10010 
        1. 09830-01010
        2. 09830-01020
        3. 09830-01040
        4. 09830-01050
      NOTE:

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath	-	-
   	Front of the Vehicle		Outside of the Vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
      NOTE:

      • Position the rear suspension member front body mounting cushion in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath	-	-
   	Front of the Vehicle		Outside of the Vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.
      NOTE:

      • Position the rear suspension member rear body mount cushion LH in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Hold	-	-
   	Turn	-	-

   1. Install SST as shown in the illustration.
      • SST: 09710-28031 
        1. 09711-02030
        2. 09711-02040
        3. 94622-51200
      • SST: 09950-60021 
        1. 09951-00720
        2. 09951-00890
      NOTE:

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

   2. Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.
      • SST: 09710-28031 
        1. 09711-02030
        2. 09711-02040
        3. 94622-51200
      • SST: 09950-60021 
        1. 09951-00720
        2. 09951-00890
      NOTE:

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath	-	-
   	Front of the Vehicle		Outside of the Vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.
      NOTE:

      • Position the rear suspension member rear body mount cushion RH in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Engine Lifter	*b	Attachment
   	Attachment and Wooden Block Placement Location	-	-

   1. Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
      WARNING:

      • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
      • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NOTE:

      • Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
      • Keep supporting the rear suspension member sub-assembly until the installation has been completed.
   2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.
   3. Install the rear suspension member sub-assembly with rear suspension member brace LH, rear suspension member brace RH, rear suspension arm bracket sub-assembly LH, rear suspension arm bracket sub-assembly RH, 4 bolts and 4 nuts.

      Bolt A 

      Torque: 158 N.m (1611 kgf/cm, 117 ft.lbf) 

      Nut B 

      Torque: 158 N.m (1611 kgf/cm, 117 ft.lbf) 

      Nut C 

      Torque: 18 N.m (184 kgf/cm, 13 ft.lbf) 

      Nut D 

      Torque: 90 N.m (918 kgf/cm, 66 ft.lbf) 

for A25A-FKS: Refer to INSTALLATION [11/2021 - ]

for T24A-FTS: Refer to INSTALLATION [03/2023 - ]

Refer to ADJUSTMENT [11/2021 - ]