Caution / Notice / Hint
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Rear wheel alignment adjustment |
|
|
Refer to RESET MEMORY / CALIBRATION [11/2021 - ] |
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) Refer to WORK PROCEDURE [03/2023 - 03/2024] |
| Rear television camera assembly optical axis (Back camera position setting)*3 | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization*3 | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] | |
| ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) | Dynamic Torque Control AWD System (for T24A-FTS, A25A-FKS (Type B)) | Refer to CALIBRATION [03/2023 - ] | |
| Suspension parts | Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [11/2021 - 03/2024] | |
| Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] | |
| Rear height control sensor sub-assembly LH | Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] |
| Gas leak from exhaust system is repaired | Perform Inspection After Repair |
|
for A25A-FKS: Refer to INITIALIZATION [11/2021 - ] for T24A-FTS: Refer to INITIALIZATION [11/2021 - ] |
*1: Also necessary after performing a tire rotation.
*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*3: The vehicle height changes because of tire replacement.
WARNING:
- To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
- The rear differential carrier assembly is very heavy. Be sure to follow the procedure described in the repair information, or the engine lifter may suddenly drop.
*a Object Exceeding Weight Limit of Engine Lifter
COMPONENTS (REMOVAL)
Fig 1: Rear Suspension Member (For Gasoline Model AWD) Removal Components [03/2023 - 03/2024] (1 Of 2)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | DIFFERENTIAL CARRIER ASSEMBLY | - | - | - | - |
| 2 | REAR STABILIZER BAR | 48812 | - | - | - |
| 3 | REAR NO. 2 SUSPENSION ARM ASSEMBLY LH | 48740F | See step 3 | - | - |
| 4 | REAR NO. 2 SUSPENSION ARM ASSEMBLY RH | 48730F | - | - | - |
| 5 | REAR NO. 1 DIFFERENTIAL MOUNT CUSHION | 41651 | See step 5 | - | - |
| 6 | FRAME WIRE | 82164 | - | - | - |
| 7 | REAR SUSPENSION MEMBER SUB-ASSEMBLY | 51206A | See step 7 | - | - |
| *A | for A25A-FKS | *B | for T24A-FTS |
| *1 | REAR SUSPENSION MEMBER BRACE LH | *2 | REAR SUSPENSION MEMBER BRACE RH |
| *3 | REAR SUSPENSION ARM BRACKET SUB-ASSEMBLY LH | *4 | REAR SUSPENSION ARM BRACKET SUB-ASSEMBLY RH |
| • | Non-reusable part | - | - |
Fig 2: Rear Suspension Member (For Gasoline Model AWD) Removal Components [03/2023 - 03/2024] (2 Of 2)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 8 | REAR UPPER CONTROL ARM ASSEMBLY LH | 48790 | See step 8 | - | - |
| 9 | REAR UPPER CONTROL ARM ASSEMBLY RH | 48770A | - | - | - |
| 10 | DIFFERENTIAL SUPPORT MEMBER CUSHION | 52281 | - | - | - |
| 11 | REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION LH | 52272A | See step 11 | - | - |
| 12 | REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION RH | 52271E | - | - | - |
| 13 | REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH | 52276A | See step 13 | - | - |
| 14 | REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH | 52275B | - | - | - |
| 15 | HOLE PLUG | - | - | - | - |
| • | Non-reusable part | - | - |