DTC P0014-00: Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1; DTC P0015-00: Camshaft Position "B" - Timing Over-Retarded Bank 1; DTC P05CE-00: Cold Start "B" Camshaft Position Timing Performance Bank 1 [11/2021 - 03/2023]: Procedure

1. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC P0014-00, P0015-00 or P05CE-00 is output	A
   DTC P0014-00, P0015-00 or P05CE-00 and other DTCs are output	B

   HINT: 

   If any DTCs other than P0014-00, P0015-00 or P05CE-00 are output, troubleshoot those DTCs first.

Result: 

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2021 - 03/2023] 

Result: 

A 

See step  2

1. Start the engine.
2. Check the engine speed while operating the cam timing oil control solenoid assembly using the GTS.

   Powertrain > Engine > Active Test 

   Tester Display
   Control the Exhaust VVT OCV Duty Ratio Bank 1

   OK

   GTS Operation	Engine Condition
   0%	Normal engine speed
   100%	Engine idles roughly or stalls

   HINT: 

   Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1].

   Refer to DATA LIST / ACTIVE TEST [11/2021 - 03/2023]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  5

Result: 

OK 

See step  3

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Turn the ignition switch off and wait for at least 30 seconds.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
2. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0014-00, P0015-00 or P05CE-00 is output	B

   HINT: 

   DTC P0014-00, P0015-00 or P05CE-00 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.

Result: 

A 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2021 - ] 

Result: 

B 

See step  5

1. Inspect the cam timing oil control solenoid assembly (for exhaust side).

   Refer to INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  11

Result: 

OK 

See step  6

1. Inspect the exhaust camshaft timing gear bolt assembly.

   Refer to ON-VEHICLE INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  13

Result: 

OK 

See step  7

1. Remove the cylinder head cover sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	10.6°	*b	21.91°
   *c	Timing Mark	*d	"0" Timing Mark
   *e	Groove	-	-

2. Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
3. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

   HINT: 

   If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.

   OK

   Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

   HINT: 

   If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  15

Result: 

NG 

See step  8

1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

   HINT: 

   Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

   Refer to INITIALIZATION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA 

Result: 

OK 

See step  9

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Turn the ignition switch off and wait for at least 30 seconds.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
2. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0014-00, P0015-00 or P05CE-00 is output	B

Result: 

A 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2021 - ] 

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [11/2021 - ] 

1. Replace the cam timing oil control solenoid assembly.

   Refer to REMOVAL [11/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  12

1. Inspect the exhaust camshaft timing gear bolt assembly.

   Refer to ON-VEHICLE INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  14

Result: 

NG 

See step  13

1. Replace the exhaust camshaft timing gear bolt assembly.

   Refer to REMOVAL [11/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  14

1. Start the engine.
2. Check the engine speed while operating the cam timing oil control solenoid assembly using the GTS.

   Powertrain > Engine > Active Test 

   Tester Display
   Control the Exhaust VVT OCV Duty Ratio Bank 1

   OK

   GTS Operation	Engine Condition
   0%	Normal engine speed
   100%	Engine idles roughly or stalls

   HINT: 

   Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1].

   Refer to DATA LIST / ACTIVE TEST [11/2021 - 03/2023]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

See step  15

1. Replace the camshaft timing exhaust gear assembly.

   Refer to REMOVAL [11/2021 - 03/2024]

   HINT: 

   Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

   Refer to INITIALIZATION [11/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  16

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Turn the ignition switch off and wait for at least 30 seconds.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  17

1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
2. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0014-00, P0015-00 or P05CE-00 is output	B

Result: 

A 

END 

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [11/2021 - ]