LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LX 600 Base >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Body Panels / Trim - Service Information (1 Of 2) >> FRONT CONSOLE BOX (w/o Cool Box) >> Removal [12/2021 - ] >> Procedure

Removal [12/2021 - ]: Procedure

  1. REMOVE REAR SEAT CONSOLE BOX LOWER PANEL (for 4-Passenger) 

    Refer to REMOVAL [12/2021 - ] 

  2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 1
  3. REMOVE BOX BOTTOM MAT 
    1. GTY1056945Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE UPPER CONSOLE PANEL ASSEMBLY 

    HINT: 

    The illustrations are representative examples, and details may differ.

    1. GTY1056539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1) Remove in this Direction (2)
      1. Apply protective tape at the position shown in the illustration.
      2. Using moulding remover B, detach the claw as shown in the illustration.
      3. Using moulding remover B, detach the claw and remove the upper console panel assembly as shown in the illustration.
      4. Disconnect the 2 connector and detach the clamp.
  5. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY 
    1. GTY1056800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here Remove in this Direction (1)
      Remove in this Direction (2) - -
  6. REMOVE FRONT CONSOLE BOX INSERT SUB-ASSEMBLY 
    1. GTY1056424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  7. REMOVE LOWER NO. 2 INSTRUMENT PANEL PAD SUB-ASSEMBLY 
    1. GTY1055755Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL PAD SUB-ASSEMBLY 
    1. Use the same procedure described for the lower No. 2 instrument panel pad subassembly.
  9. REMOVE SHIFTING HOLE BEZEL 
    1. GTY1055582Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  10. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY 

    HINT: 

    The illustrations are representative examples, and details may differ.

    1. except 4-Passenger:
      GTY1056232Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here Remove in this Direction (1)
      Remove in this Direction (2) Remove in this Direction (3)
      1. Insert moulding remover B in the position shown in the illustration.
      2. Place your hand in the gap as shown in the illustration, detach the claw.
      3. Insert moulding remover B in the position shown in the illustration.
      4. Place your hand in the gap as shown in the illustration, detach the claw.
      5. Place your hand as shown in the illustration, detach the claw and guide and remove the console rear end panel sub-assembly.
      6. Disconnect the 2 connectors and detach the clamp.
      7. Using a thin-bladed screwdriver, detach the claw and remove the connector cover.

        HINT: 

        Tape the thin-bladed screwdriver tip before use.

    2. for 4-Passenger:
      GTY1055628Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here Remove in this Direction (1)
      Remove in this Direction (2) Remove in this Direction (3)
      1. Insert moulding remover B in the position shown in the illustration.
      2. Place your hand in the gap as shown in the illustration, detach the claw.
      3. Insert moulding remover B in the position shown in the illustration.
      4. Place your hand in the gap as shown in the illustration, detach the claw.
      5. Place your hand as shown in the illustration, detach the claw and guide remove the console rear end panel sub-assembly.
  11. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY 
    1. GTY1058676Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
scientia non olet · About LEMON Manuals