Seat Heater for Front Right Seat does not Operate [10/2017 - 10/2020]: Procedure

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [10/2017 - ]

   Body Electrical > Air Conditioner > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  2

1. Check for DTCs.

   Refer to DTC CHECK / CLEAR [10/2017 - ]

   Body Electrical > Air Conditioner > Trouble Codes 

   OK

   DTC B14C0 is not output.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2017 - ] 

Result: 

OK 

See step  3

1. Disconnect the Q11 seat heater control sub-assembly RH connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   Q11-3 (IG) - Body ground	Power switch on (IG)	11 to 14 V
   	Power switch off	Below 1 V
   Q11-1 (+B1) - Body ground	Power switch off	11 to 14 V
   Q11-8 (+B2) - Body ground	Power switch off	11 to 14 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

1. Remove the separate type front seat cushion cover RH.

   Refer to REMOVAL [10/2017 - 09/2018] , or refer to REMOVAL [09/2018 - 10/2020]

2. Inspect the separate type front seat cushion cover RH.

   Refer to INSPECTION [10/2017 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SEPARATE TYPE FRONT SEAT CUSHION COVER RH. Refer to  REMOVAL [10/2017 - 09/2018]  , or refer to  REMOVAL [09/2018 - 10/2020] 

Result: 

OK 

See step  5

1. Remove the separate type front seatback cover RH.

   Refer to REMOVAL [10/2017 - 09/2018] , or refer to REMOVAL [09/2018 - 10/2020]

2. Inspect the separate type front seatback cover RH.

   Refer to INSPECTION [10/2017 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SEPARATE TYPE FRONT SEATBACK COVER RH. Refer to  REMOVAL [10/2017 - 09/2018]  , or refer to  REMOVAL [09/2018 - 10/2020] 

Result: 

OK 

See step  6

1. Disconnect the Q15 separate type front seat cushion cover RH connector.
2. Disconnect the Q11 seat heater control sub-assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Q15-6 - Q11-10 (E)	Always	Below 1 Ω
   Q15-6 or Q11-10 (E) - Other terminals and body ground	Always	10 kΩ or higher
   Q15-1 - Q11-7 (Heater Output 1)	Always	Below 1 Ω
   Q15-1 or Q11-7 (Heater Output 1) - Other terminals and body ground	Always	10 kΩ or higher
   Q15-3 - Q11-12 (Heater Output 2)	Always	Below 1 Ω
   Q15-3 or Q11-12 (Heater Output 2) - Other terminals and body ground	Always	10 kΩ or higher
   Q15-2 - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  7

1. Disconnect the Q15 separate type front seat cushion cover RH connector.
2. Disconnect the G63 and G64 air conditioning amplifier assembly connectors.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Q15-4 - G63-18 (TSR)	Always	Below 1 Ω
   Q15-4 or G63-18 (TSR) - Other terminals and body ground	Always	10 kΩ or higher
   Q15-5 - G64-8 (SG-5)	Always	Below 1 Ω
   Q15-5 or G64-8 (SG-5) - Other terminals and body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  8

1. Disconnect the Q11 seat heater control sub-assembly RH connector.
2. Disconnect the G63 air conditioning amplifier assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Q11-4 (PWM) - G63-16 (SHP+)	Always	Below 1 Ω
   Q11-4 (PWM) or G63-16 (SHP+) - Other terminals and body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  9

1. Temporarily replace the seat heater control sub-assembly RH with a new or known good one.

   Refer to REMOVAL [10/2017 - 09/2018] , or refer to REMOVAL [09/2018 - 10/2020]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Check the seat heater.

   Refer to OPERATION CHECK [10/2017 - 10/2022]

   OK

   The seat heater operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (SEAT HEATER CONTROL SUB-ASSEMBLY RH WAS DEFECTIVE) 

Result: 

NG 

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [10/2017 - ]