LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 91 (Engine Intake / Exhaust System - Service Information (Coupe)) >> Exhaust Pipe >> Removal [09/2023 - ] >> Procedure

Removal [09/2023 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE REAR FLOOR SIDE MEMBER COVER LH 
    1. w/o Front Suspension Member Brace:
      1. GTY1241832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Nut
        Screw

        Remove the 2 clips, 3 bolts, nut, screw and rear floor side member cover LH.

    2. w/ Front Suspension Member Brace:
      1. Remove the 3 clips, 3 bolts, nut, screw, plate washer and rear floor side member cover LH.
        GTY1242456Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Nut
        Screw
        *a Clip and Plate Washer
  2. REMOVE REAR FLOOR SIDE MEMBER COVER RH 
    1. w/o Front Suspension Member Brace:
      1. Remove the 2 clips, 3 bolts, nut, screw and rear floor side member cover RH.
        GTY1241794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Nut
        Screw
    2. w/ Front Suspension Member Brace:
      1. Remove the 3 clips, 3 bolts, nut, screw, plate washer and rear floor side member cover RH.
        GTY1242463Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Nut
        Screw
        *a Clip and Plate Washer
  3. REMOVE FRONT FENDER SEAL LH 
    1. w/o Front Suspension Member Brace:
      1. GTY1241725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Grommet

        Remove the 3 clips, 3 plate washers, grommet and front fender seal LH.

    2. w/ Front Suspension Member Brace:
      1. GTY947539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Grommet

        Remove the 4 clips, 4 plate washers, grommet and front fender seal LH.

  4. REMOVE FRONT FENDER SEAL RH 
    1. w/o Front Suspension Member Brace:
      1. GTY1241826Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Grommet

        Remove the 3 clips, 3 plate washers, grommet and front fender seal RH.

    2. w/ Front Suspension Member Brace:
      1. GTY947920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Grommet

        Remove the 4 clips, 4 plate washers, grommet and front fender seal RH.

  5. REMOVE FRONT FLOOR COVER LH 
    1. w/o Front Suspension Member Brace:
      1. GTY1241727Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Grommet
        Nut

        Remove the 4 grommets, 6 clips, nut, bolt and front floor cover LH.

    2. w/ Front Suspension Member Brace:
      1. GTY1242387Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Grommet
        Nut

        Remove the 3 grommets, 6 clips, nut, bolt and front floor cover LH.

  6. REMOVE FRONT FLOOR COVER RH 
    1. w/o Front Suspension Member Brace:
      1. GTY1241729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Grommet
        Nut

        Remove the 4 grommets, 6 clips, nut, bolt and front floor cover RH.

    2. w/ Front Suspension Member Brace:
      1. GTY1242180Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Bolt
        Grommet
        Nut

        Remove the 3 grommets, 6 clips, nut, bolt and front floor cover RH.

  7. REMOVE FRONT SEAT ASSEMBLY 

    Refer to REMOVAL [05/2023 - ]

  8. DISCONNECT HEATED OXYGEN SENSOR CONNECTOR 

    Refer to PROCEDURE - Step 8

  9. REMOVE HEATED OXYGEN SENSOR (for Bank 1) 

    Refer to PROCEDURE - Step 9

  10. REMOVE HEATED OXYGEN SENSOR (for Bank 2) 

    Refer to PROCEDURE - Step 10

  11. REMOVE FRONT NO. 1 FLOOR CROSS BRACE LH (w/ Front Suspension Member Brace) 
    1. Remove the 2 bolts, nut and front No. 1 floor cross brace LH.
      GTY947219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Nut
  12. REMOVE FRONT NO. 1 FLOOR CROSS BRACE RH (w/ Front Suspension Member Brace) 
    1. Remove the 2 bolts, nut and front No. 1 floor cross brace RH.
      GTY947482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Nut
  13. REMOVE FRONT CENTER FLOOR BRACE SUB-ASSEMBLY 
    1. Remove the 12 bolts and front center floor brace sub-assembly.
      GTY819183Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR 
    1. Remove the 3 nuts and No. 2 differential support protector.
      GTY819223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR 
    1. Remove the 3 nuts and No. 1 differential support protector.
      GTY819221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE REAR NO. 4 BUMPER SIDE SUPPORT LH 
    1. Remove the 2 screws, 2 clips, grommet and rear No. 4 bumper side support LH.
      GTY819182Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE REAR NO. 4 BUMPER SIDE SUPPORT RH 
    1. Remove the 2 screws, 2 clips, grommet and rear No. 4 bumper side support RH.
      GTY819181Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE FRONT EXHAUST PIPE ASSEMBLY 
    1. Remove the 4 bolts and 4 nuts to disconnect the front exhasut pipe assembly from the exhaust manifold sub-assembly LH and exhaust manifold sub-assembly RH.
      GTY818642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 4 bolts, 4 nuts and front exhaust pipe assembly from the exhaust tailpipe assembly.
      GTY947923Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 4 gaskets.
  19. REMOVE EXHAUST TAILPIPE ASSEMBLY 
    WARNING:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

    1. for Type A:

      Detach the 2 clamps and disconnect the 4 connectors.

      GTY818636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Type B:

      Detach the 2 clamps and disconnect the 2 connectors.

      GTY1084852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 6 exhaust pipe supports and exhaust tailpipe assembly.
      GTY818637Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE EXHAUST PIPE GAS CONTROL ACTUATOR SUB-ASSEMBLY 
    1. for Type A:
      GTY1084528Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for RH Side
      *B for LH Side
      1. Remove the 6 bolts and 4 nuts.
      2. Remove the 2 exhaust pipe gas control actuator sub-assemblies from the exhaust tailpipe assembly.
    2. for Type B:
      GTY1084646Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for RH Side
      *B for LH Side
      1. Remove the 6 bolts and 4 nuts.
      2. Remove the 2 exhaust pipe gas control actuator sub-assemblies from the exhaust tailpipe assembly.
scientia non olet · About LEMON Manuals