LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 23 (Supplemental Restraint System - Service Information (Coupe) (2 Of 2)) >> Side Airbag Sensor >> Installation [05/2023 - ] >> Procedure

Installation [05/2023 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL DOOR SIDE AIRBAG SENSOR LH 
    1. Check that the engine switch is off.
    2. Check that the cable is disconnected from the negative (-) battery terminal.
      WARNING:
      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
        GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • If this procedure is performed without disconnecting the negative (-) battery terminal, the airbag may deploy even if an impact is applied only to the door side airbag sensor LH. Therefore, make sure that the negative (-) battery terminal is disconnected before performing this procedure.
        GTY796829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Attach the claw to hold the door side airbag sensor LH in place.
    4. Install the nut.

      Torque: 9.0 N.m (92 kgf/cm, 80 in.lbf) 

      NOTE:
      • If the door side airbag sensor LH has been dropped, replace it with a new one.
      • When installing the door side airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
      • Tighten the nut while holding the door side airbag sensor LH.
    5. Check that there is no looseness in the installation parts of the door side airbag sensor LH.
    6. Connect the airbag connector.
      NOTE:

      When connecting any airbag connector, take care not to damage the airbag wire harness.

      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.
        GTY824216Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Correct *b Incorrect
        *c CPA *d Housing
      2. While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).
        NOTE:

        Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.

        GTY810567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a CPA Upper Part *b Housing Lock
        *c CPA *d Connection is Completed
  2. INSTALL NO. 1 FRONT DOOR HOLE COVER SUB-ASSEMBLY LH 
    1. for Driver Side:
      1. Align with the installation holes on the vehicle side and No. 1 front door hole cover sub-assembly LH.
      2. Pass the clip through the installation holes so that the clip knob is perpendicular.
        GTY798463Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Knob
        *b Lock Mark
        *c Lock Position
        Rotate in this Direction
      3. With the clip knob installed perpendicular, rotate the clip knob 45° clockwise to align it to the lock mark and lock it.

        HINT: 

        Use the same procedure for the other clips.

    2. for Passenger Side:
      1. Align with the installation holes on the vehicle side and No. 1 front door hole cover sub-assembly RH.
      2. Pass the clip through the installation holes so that the clip knob is perpendicular.
        GTY780895Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Knob
        *b Lock Mark
        *c Lock Position
        Rotate in this Direction
      3. With the clip knob installed perpendicular, rotate the clip knob 45° clockwise to align it to the lock mark and lock it.

        HINT: 

        Use the same procedure for the other clips.

    3. Check that the clip knob is in the lock position.
  3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Driver Side) 

    Refer to PROCEDURE - Step 39

  4. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH (for Front Passenger Side) 

    Refer to PROCEDURE - Step 43

  5. INSTALL FRONT DOOR TRIM COVER SUB-ASSEMBLY LH (for Driver Side) 

    Refer to PROCEDURE - Step 41

  6. INSTALL FRONT DOOR ASSIST GRIP ASSEMBLY RH (for Front Passenger Side) 

    Refer to PROCEDURE - Step 45

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

  8. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL 

    HINT: 

    When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

    Refer to AUTOMATIC LEARNING CHART [05/2023 - ]

  9. INSTALL NO. 2 DECK BOARD 

    Refer to PROCEDURE - Step 13

  10. PERFORM DIAGNOSTIC SYSTEM CHECK 

    Refer to DTC CHECK / CLEAR [04/2020 - ]

  11. CHECK SRS WARNING LIGHT 

    Refer to OPERATION CHECK [04/2020 - ]

scientia non olet · About LEMON Manuals