LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 137 (Automatic Transmission System - Service Information (Coupe) (2 Of 2)) >> Automatic Transmission Assembly >> Removal [04/2020 - 05/2023] >> Procedure

Removal [04/2020 - 05/2023]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [03/2017 - 05/2023]

  2. REMOVE EXHAUST MANIFOLD 

    Refer to REMOVAL [03/2017 - 05/2023]

  3. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY 
    GTY825775Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 bolts and No. 1 exhaust pipe support bracket sub-assembly from the automatic transmission assembly.
  4. DISCONNECT WIRE HARNESS 
    1. Disconnect the transmission wire connector.
      GTY958161Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Transmission Wire Connector - -
      Wire Harness Connector Bolt
      Pull Down the Lever - -

      HINT: 

      Disconnect the claw, pull down the lever, and then disconnect the transmission wire connector.

    2. Disconnect the wire harness connector.
    3. Remove the 4 bolts and disconnect the wire harness from the automatic transmission assembly.
  5. REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR 

    Refer to PROCEDURE - Step 5

  6. REMOVE STARTER ASSEMBLY 

    Refer to PROCEDURE - Step 6

  7. REMOVE FLYWHEEL HOUSING SIDE COVER 

    Refer to PROCEDURE - Step 7

  8. DISCONNECT OIL COOLER TUBE WITH OIL COOLER HOSE 
    1. Slide the 2 hose clips and disconnect the 2 oil cooler hoses from the automatic transmission assembly.
      GTY825779Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 bolts and disconnect the oil cooler tubes from the engine assembly and automatic transmission assembly.

      HINT: 

      When removing the automatic transmission assembly, hold the oil cooler tube in a position so that the oil cooler tube and automatic transmission assembly do not interfere with one another.

  9. REMOVE ENGINE REAR MOUNTING MEMBER 
    1. GTY958126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Nut and Spring Washer

      Remove the nut, spring washer and 2 bolts and disconnect the throttle link connecting rod assembly from the shift control actuator assembly.

    2. Remove the 3 nuts and engine rear mounting member.
      GTY825777Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE REAR ENGINE MOUNTING INSULATOR 
    1. Remove the 4 bolts and rear engine mounting insulator.
      GTY825776Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT 
    1. Turn the crankshaft to gain access to each bolt and remove the 6 drive plate and torque converter clutch setting bolts while holding the crankshaft pulley bolt with a wrench.
      GTY825778Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY 
    1. Using a rope or equivalent, support the automatic transmission assembly at the positions shown in the illustration.
      WARNING:

      Secure the engine assembly to the engine lifter using a belt, etc. to prevent it from falling.

      GTY820247Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 10 bolts and automatic transmission assembly.
      GTY825757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      WARNING:
      • Do not raise the automatic transmission assembly more than necessary.
      • Make sure to confirm the center of the gravity of the automatic transmission assembly when supporting it.
      NOTE:
      • Do not use excessive force to pry out the automatic transmission assembly when separating it from the engine assembly to prevent the knock pins from being damaged.
      • When removing the automatic transmission assembly, make sure that the oil cooler tube does not become damaged.
      • Do not allow the wooden blocks or equivalent to contact the transmission oil pan assembly when supporting the automatic transmission assembly, as the transmission oil pan assembly may be deformed as a result.
  13. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY 
    1. Put matchmarks on the automatic transmission assembly and torque converter clutch assembly.
      GTY783076Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    2. Remove the torque converter clutch assembly from the automatic transmission assembly.
  14. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY 

    See step  1

scientia non olet · About LEMON Manuals