LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> ES 350 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - Service Information >> HEADUP Display >> Disassembly [06/2018 - ] >> Procedure

Disassembly [06/2018 - ]: Procedure

  1. PRECAUTION 
    1. Static electricity countermeasures SST
      1. SST: Desktop anti-static mat set
        GTY798036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        • SST: 09890-47010 
          1. 09891-04010
          2. 09891-04020
          3. 09891-04030
          4. 09891-04040
        • Anti-static mat
        • Wristband
        • Wristband connection wire (No. 1 grounding wire)
        • Ground connection wire (No. 2 grounding wire)
    2. Precautions during replacement
      1. Precautions during procedures:
        1. Before performing any procedures, touch an unpainted metal part or ground bolt of the vehicle to eliminate any static electricity.
        2. To prevent damage to electrical equipment, disconnect the battery power supply before installing and removing electrical equipment.
        3. Never touch the electronic parts of a printed wire board or the pins of an integrated circuit.
        4. When performing procedures, do not allow clothing to come near or contact parts.
      2. Wear SST (wristband) firmly on your wrist.
        GTY798036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Connect SST (No. 2 grounding wire) and SST (anti-static mat) to an appropriate grounding point in the workspace and on the work table.

        HINT: 

        When working inside the vehicle: 

        Connect SST (No. 2 grounding wire) to an unpainted metal part or ground bolt, etc.

        GTY800309Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Connect SST (No. 1 grounding wire), SST (wristband) and SST (anti-static mat).
      5. Always place the meter mirror sub-assembly and its components on SST (anti-static mat).
  2. REMOVE NO. 1 COMBINATION SPEEDOMETER CUSHION 
    1. Remove the No. 1 combination speedometer cushion.
      GTY832357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE NO. 1 COMBINATION METER MIRROR PLATE 
    NOTE:
    • Prevention of static electricity is required during this procedure.
    • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
    1. Remove the 7 screws.
      GTY832360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pull the No. 1 combination meter mirror plate in the direction indicated by the arrow (1) shown in the illustration to disengage the 2 claws.
      GTY796034Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
    3. Move the No. 1 combination meter mirror plate direction indicated by the arrow (2) shown in the illustration.
      NOTE:

      Do not apply excessive force when move the No. 1 combination meter mirror plate.

    4. Disengage the clamp.
      GTY798413Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the screw.
      GTY798415Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disengage the 2 guides as shown in the illustration to remove the No. 1 combination meter mirror plate.
      GTY818542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
scientia non olet · About LEMON Manuals