LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> ES 300h Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 19 (Engine Control System (2GR-FKS) - Service Information) >> Heated Oxygen Sensor >> Installation [06/2018 - ] >> Procedure

Installation [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL HEATED OXYGEN SENSOR (for Bank 2) 

    HINT: 

    Perform "Inspection After Repair" after replacing the heated oxygen sensor.

    Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - ]

    1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly (TWC: Rear Catalyst).
      GTY745995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N.m (449 kgf/cm, 32 ft.lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [06/2018 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N.m (384 kgf/cm, 28 ft.lbf)

  2. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) 

    Refer to PROCEDURE - Step 14

  3. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side) 

    Refer to PROCEDURE - Step 4

  4. INSTALL BODY MOUNTING PLATE 

    Refer to PROCEDURE - Step 5

  5. INSTALL FRONT FLOOR COVER LH 

    Refer to PROCEDURE - Step 9

  6. INSTALL FRONT FLOOR COVER RH 

    Refer to PROCEDURE - Step 10

  7. INSTALL HEATED OXYGEN SENSOR (for Bank 1) 

    HINT: 

    Perform "Inspection After Repair" after replacing the heated oxygen sensor.

    Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - ]

    1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly (TWC: Rear Catalyst).
      GTY743695Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N.m (449 kgf/cm, 32 ft.lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [06/2018 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N.m (384 kgf/cm, 28 ft.lbf)

    2. Engage the wire harness clamp.
    3. Connect the heated oxygen sensor connector.
  8. INSPECT FOR EXHAUST GAS LEAK 

    Refer to PROCEDURE - Step 13

  9. INSTALL NO. 2 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 68

  10. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 70

  11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 71

  12. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 72

  13. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing the heated oxygen sensor.

      Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - ]

scientia non olet · About LEMON Manuals