LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> ES 300h Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 139 (Automatic Transmission System (UA80E) - Service Information (1 Of 4)) >> Oil Cooler >> Removal [07/2019 - 10/2019] >> Procedure

Removal [07/2019 - 10/2019]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE BATTERY 

    Refer to REMOVAL [06/2018 - 08/2021]

  2. REMOVE ECM 

    Refer to REMOVAL [06/2018 - 10/2019]

  3. REMOVE BATTERY CLAMP SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25

  4. REMOVE FRONT WHEEL LH 

    Refer to REMOVAL [06/2018 - ]

  5. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 7

  6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 8

  7. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 9

  8. REMOVE NO. 3 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10

  9. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 12

  10. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 1

  11. DRAIN AUTOMATIC TRANSAXLE FLUID 

    See step  7

  12. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE 
    1. Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.
      GTY865207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.

  13. DISCONNECT INLET NO. 1 OIL COOLER HOSE 
    1. Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.
      GTY865179Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.

  14. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE 
    1. Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.
      GTY932125Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.
      GTY762233Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.

    3. Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.
      GTY762231Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.

    4. Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.
      GTY913098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Oil Cooler Tube Sub-assembly without Hose
      *2 Inlet No. 1 Oil Cooler Hose
      *3 Inlet No. 2 Oil Cooler Hose
      *4 Outlet No. 1 Oil Cooler Hose
      *5 Outlet No. 2 Oil Cooler Hose
  15. DISCONNECT NO. 1 WATER BY-PASS HOSE 
    1. Disengage the 3 clamps to remove the transmission breather clamp.
      GTY768649Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.
      GTY740941Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

  16. DISCONNECT WATER BY-PASS HOSE ASSEMBLY 
    1. Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.
      GTY768648Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

  17. REMOVE TRANSMISSION OIL COOLER 
    1. Type A:
      1. Remove the 3 bolts.
        GTY762235Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Disengage the hook to remove the transmission oil cooler from the automatic transaxle case sub-assembly.

        HINT: 

        Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.

    2. Type B:
      1. Remove the 3 bolts and transmission oil cooler from the automatic transaxle case sub-assembly.

        HINT: 

        Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.

        GTY865164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals