LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> ES 300h Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 121 (Engine Mechanical System (A25A-FKS) - Service Information (1 Of 3)) >> Cylinder Head Gasket >> Removal [09/2022 - ] >> Procedure

Removal [09/2022 - ]: Procedure

WARNING: This page is about a different car, the 2024 Lexus ES 250, 2023 Lexus ES 250, 2022 Lexus ES 250, and 2021 Lexus ES 250. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND 

    Refer to REMOVAL [09/2022 - ]

  2. REMOVE ENGINE HANGERS 

    Refer to PROCEDURE - Step 67

  3. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 5

  4. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 5

  5. REMOVE COMPRESSOR ASSEMBLY WITH PULLEY 

    Refer to PROCEDURE - Step 4

  6. REMOVE NO. 2 ENGINE COVER 

    Refer to PROCEDURE - Step 5

  7. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 6

  8. REMOVE TIMING GEAR COVER INSULATOR 

    Refer to PROCEDURE - Step 8

  9. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  10. REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY) 

    Refer to PROCEDURE - Step 10

  11. SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR 

    Refer to PROCEDURE - Step 16

  12. REMOVE MANIFOLD STAY 

    Refer to PROCEDURE - Step 18

  13. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 19

  14. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY 

    Refer to PROCEDURE - Step 4

  15. REMOVE THROTTLE BODY GASKET 

    Refer to PROCEDURE - Step 5

  16. REMOVE EGR COOLER ASSEMBLY 

    Refer to PROCEDURE - Step 4

  17. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 6

  18. REMOVE EGR VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 18

  19. REMOVE NO. 3 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 19

  20. REMOVE NO. 2 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 20

  21. REMOVE INTAKE MANIFOLD 

    Refer to PROCEDURE - Step 11

  22. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET 

    Refer to PROCEDURE - Step 12

  23. DISCONNECT FUEL TUBE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 6

  24. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 24

  25. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure) 

    Refer to PROCEDURE - Step 8

  26. REMOVE NO. 7 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 26

  27. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  28. REMOVE NO. 1 DELIVERY PIPE SPACER 

    Refer to PROCEDURE - Step 4

  29. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 5

  30. REMOVE NO. 5 ENGINE WIRE 

    Refer to PROCEDURE - Step 6

  31. REMOVE PORT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 7

  32. REMOVE FUEL DELIVERY PIPE 

    Refer to PROCEDURE - Step 2

  33. REMOVE DIRECT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 3

  34. REMOVE FUEL INJECTOR SEAL 

    Refer to PROCEDURE - Step 4

  35. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  36. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 

    Refer to PROCEDURE - Step 39

  37. REMOVE PURGE VALVE (PURGE VSV) 

    Refer to PROCEDURE - Step 1

  38. REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 2

  39. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side) 

    Refer to PROCEDURE - Step 2

  40. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side) 

    Refer to PROCEDURE - Step 3

  41. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY 

    Refer to PROCEDURE - Step 4

  42. REMOVE O-RING 

    Refer to PROCEDURE - Step 5

  43. REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY 

    Refer to PROCEDURE - Step 6

  44. REMOVE CAM TIMING CONTROL MOTOR O-RING 

    Refer to PROCEDURE - Step 7

  45. REMOVE VACUUM PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 3

  46. REMOVE CRANKSHAFT PULLEY ASSEMBLY 

    Refer to PROCEDURE - Step 18

  47. REMOVE WATER OUTLET 

    Refer to PROCEDURE - Step 19

  48. REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 20

  49. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 21

  50. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 22

  51. REMOVE ENGINE MOUNTING BRACKET RH 

    Refer to PROCEDURE - Step 23

  52. REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 26

  53. REMOVE TIMING CHAIN COVER OIL SEAL 

    Refer to PROCEDURE - Step 27

  54. SET NO. 1 CYLINDER TO TDC (COMPRESSION) 

    Refer to PROCEDURE - Step 28

  55. REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 29

  56. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 30

  57. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 31

  58. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 32

  59. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 33

  60. REMOVE NO. 1 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 34

  61. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 35

  62. REMOVE TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 36

  63. REMOVE FUEL PUMP LIFTER GUIDE 

    Refer to PROCEDURE - Step 39

  64. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 40

  65. REMOVE CAMSHAFT BEARING CAP 

    Refer to PROCEDURE - Step 41

  66. REMOVE CAMSHAFT 

    Refer to PROCEDURE - Step 42

  67. REMOVE NO. 2 CAMSHAFT 

    Refer to PROCEDURE - Step 43

  68. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 45

  69. REMOVE VALVE LASH ADJUSTER ASSEMBLY 

    Refer to PROCEDURE - Step 46

  70. REMOVE VALVE STEM CAP 

    Refer to PROCEDURE - Step 47

  71. REMOVE CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 49

  72. REMOVE CYLINDER HEAD GASKET 
    GTY759932Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the cylinder head gasket from the cylinder block sub-assembly.
  73. INSPECT CYLINDER HEAD SET BOLT 

    Refer to PROCEDURE - Step 18

  74. INSPECT CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 1

scientia non olet · About LEMON Manuals