DTC C1434: Steering Angle Sensor Output [10/2018 - ]: Procedure

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [10/2018 - ]

   Chassis > ABS/VSC/TRAC > Clear DTCs 

2. Turn the power switch off.
3. Turn the power switch on (IG) again and check that no CAN communication system DTCs are output.

   Refer to DIAGNOSIS SYSTEM [10/2018 - 10/2019] , or refer to DIAGNOSIS SYSTEM [10/2019 - 08/2021] , or refer to DIAGNOSIS SYSTEM [08/2021 - 07/2022] , or refer to DIAGNOSIS SYSTEM [07/2022 - ]

4. Turn the power switch on (READY).
5. Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

   Refer to DTC CHECK / CLEAR [10/2018 - ]

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   Result

   Result	Proceed to
   DTC C1434 is output.	A
   CAN communication system DTCs are output.	B
   Speed sensor and/or yaw rate and acceleration sensor DTCs are output.	C

   HINT: 

   • If there is a malfunction in a speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output even though the steering sensor is normal.
   • If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and inspect the steering sensor.

Result: 

B 

INSPECT CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ] 

Result: 

C 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2018 - 08/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - 07/2022]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2022 - ] 

Result: 

A 

See step  2

1. Turn the power switch off.
2. Check that the steering sensor has been installed properly.

   Refer to INSTALLATION [10/2018 - ]

   OK

   The steering sensor installation is normal.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

INSTALL STEERING SENSOR CORRECTLY. Refer to  INSTALLATION [10/2018 - ] 

Result: 

OK 

See step  3

1. Remove the steering wheel and column cover.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to Steering Sensor)

2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

   OK

   The connector is securely connected.

3. Disconnect the steering sensor connector.
4. Check both the connector case and the terminals for deformation and corrosion.

   OK

   No deformation or corrosion.

5. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   F53-4 (BAT) - Body ground	Always	11 to 14 V
   F53-9 (IG1) - Body ground	Power switch on (IG)	11 to 14 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) 

Result: 

OK 

See step  4

1. Turn the power switch off.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to Steering Sensor)

2. Measure the resistance according to the value(s) in the table below.
   NOTE:

   Before measuring the resistance of the steering sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.

   Standard Resistance

   Tester Connection	Switch Condition	Specified Condition
   F53-6 (ESS) - Body ground	1 minute after power switch off	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE STEERING SENSOR. Refer to  REMOVAL [10/2018 - 07/2022]  , or refer to  REMOVAL [07/2022 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)