DTC B150A: Lost Communication with HMI-LAN [12/2017 - 08/2019]: Procedure

1. Choose the model to be inspected.

   Result

   Result	Proceed to
   w/ Navigation System	A
   w/o Navigation System	B

Result: 

B 

See step  5

Result: 

A 

See step  2

1. Check if navigation system DTCs are output.

   Refer to DTC CHECK / CLEAR [10/2015 - 08/2019]

   Body Electrical > Navigation System > Trouble Codes 

   Result

   Result	Proceed to
   Navigation system DTCs are not output	A
   Navigation system DTCs are output	B

Result: 

B 

GO TO NAVIGATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - 08/2019] 

Result: 

A 

See step  3

1. Disconnect the J11 combination meter assembly connector.
2. Disconnect the J50 radio receiver assembly connector.
3. Measure the resistance according to the value (s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   J11-9 (TX-) - J50-21 (CNL2)	Always	Below 1 Ω
   J11-10 (TX+) - J50-20 (CNH2)	Always	Below 1 Ω
   J11-9 (TX-) or J50-21 (CNL2) - Body ground	Always	10 kΩ or higher
   J11-10 (TX+) or J50-20 (CNH2) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

1. Replace the combination meter assembly with a new one.

   Refer to REMOVAL [08/2016 - 03/2018] , or refer to REMOVAL [03/2018 - 08/2019]

2. Turn the power switch on (IG) and wait 30 seconds.
   NOTE:

   A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.

3. Operate the steering pad switch assembly and check that the audio tab illuminates.
4. Check for DTCs.

   Refer to DTC CHECK / CLEAR [10/2015 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   Result

   Result	Proceed to
   The audio tab illuminates and DTC B150A is not output	A
   The audio tab does not illuminate and DTC B150A is output	B

Result: 

A 

END 

Result: 

B 

REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [08/2016 - 03/2018]  , or refer to  REMOVAL [03/2018 - 08/2019] 

1. Check if audio and visual system DTCs are output.

   Refer to DTC CHECK / CLEAR [12/2017 - 08/2019]

   Body Electrical > Navigation System > Trouble Codes 

   Result

   Result	Proceed to
   Audio and visual system DTCs are not output	A
   Audio and visual system DTCs are output	B

Result: 

B 

GO TO AUDIO AND VISUAL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2017 - 08/2019] 

Result: 

A 

See step  6

1. Disconnect the J11 combination meter assembly connector.
2. Disconnect the J55 radio receiver assembly connector.
3. Measure the resistance according to the value (s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   J11-9 (TX-) - J55-4 (CNL1)	Always	Below 1 Ω
   J11-10 (TX+) - J55-3 (CNH1)	Always	Below 1 Ω
   J11-9 (TX-) or J55-4 (CNL1) - Body ground	Always	10 kΩ or higher
   J11-10 (TX+) or J55-3 (CNH1) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  7

1. Replace the combination meter assembly with a new one.

   Refer to REMOVAL [08/2016 - 03/2018] , or refer to REMOVAL [03/2018 - 08/2019]

2. Turn the power switch on (IG) and wait 30 seconds.
   NOTE:

   A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.

3. Operate the steering pad switch assembly and check that the audio tab illuminates.
4. Check for DTCs.

   Refer to DTC CHECK / CLEAR [10/2015 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   Result

   Result	Proceed to
   The audio tab illuminates and DTC B150A is not output	A
   The audio tab does not illuminate and DTC B150A is output	B

Result: 

A 

END 

Result: 

B 

REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2017 - 03/2018]  , or refer to  REMOVAL [03/2018 - 08/2019]